GRAPHITE 59G188 Übersetzung Der Originalanleitung Seite 11

• Use the quick-action flange only with abrasive and cutting
discs. Use only undamaged and properly functioning
flanges.
• In the event of a temporary mains power failure or after
removing the plug from the power socket with the switch in the
" on" position, the switch must be unlocked and set to the off
position before restarting.
ATTENTION: The device is intended for indoor operation.
In spite of the inherently safe design, the use of safety
measures and additional protective measures, there is always
a residual risk of injury at work
Explanation of the used pictograms
1.Caution Take special precautions
2.Read the operating instructions, observe the warnings and
safety conditions contained therein!
3.Use personal protective equipment (safety goggles, ear
protection, dust mask)
4.Wear protective gloves
5.Disconnect the power cable before servicing or repairing.
6.Keep children away from the tool
7.Protect from rain
8.Secondary protection class
CONSTRUCTION AND APPLICATION
The angle grinder is a class II insulated hand-held power tool. The
machine is driven by a single-phase commutator motor, the speed of
which is reduced via a geared angle gear. It can be used for both
grinding and cutting. This type of power tool is widely used for
removing all types of burrs from the surface of metal parts, surface
treatment of welds, cutting through thin-walled pipes and small metal
parts, etc. With the appropriate accessories, the angle grinder can be
used not only for cutting and grinding but also for cleaning e.g. rust,
paint coatings, etc.
Its areas of use include a wide range of repair and construction
work not only related to metals. The angle grinder can also be used
to cut and grind building materials, e.g. brick, paving stones,
ceramic tiles, etc.
• The appliance is intended for dry use only, not for polishing.
Do not misuse the power tool
• Misuse.
• Do not handle materials containing asbestos. Asbestos is
carcinogenic.
• Do not work with materials whose dusts are flammable or
explosive. When working with the power tool, sparks are
generated which may ignite the vapours emitted.
• Cut-off wheels must not be used for grinding work. Cut-off
wheels work with the side face and grinding with the front face
of such a wheel may cause damage to the wheel resulting in a
risk of personal injury to the operator.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit
shown on the graphic pages of this manual.
1.Spindle lock button
2.Switch
3.Additional handle
4.Shield
5.External flange
6.Inner flange
7. lever (shield covers)
8. speed control knob
9.Power cable
10.Special key
* There may be differences between the drawing and the
product.
EQUIPMENT AND ACCESSORIES
1.Shield
2.Special spanner
3.Additional handle
PREPARATION FOR WORK
FITTING AN AUXILIARY HANDLE
The auxiliary handle (3) is installed in one of the holes on the
grinder head. The use of a sander with an auxiliary handle is
recommended. If you hold the sander with both hands while
working (also using the auxiliary handle), there is less risk of your
hand the rotating disc or brush and being injured by kickback.
INSTALLATION AND ADJUSTMENT OF THE SHIELD
The blade guard protects the operator from debris, accidental
contact with the work tool or sparks. It should always be fitted with
extra care taken to ensure that its covering part faces the operator.
The design of the blade guard attachment allows tool-free
adjustment of the guard to the optimum position.
• Loosen and pull back the lever (7) on the disc guard (4).
• Rotate the disc guard (4) to the desired position.
• Lock by lowering the lever (7).
• Removing and adjusting the disc guard is done in reverse
order to its installation.
TOOL REPLACEMENT
• Work gloves must be worn during tool changing operations.
• The spindle lock button (1) is only to be used to lock the
spindle of the grinder when mounting or dismounting the work
tool. It must not be used as a brake button while the disc is
spinning. Doing so may damage the grinder or injure the user.
DISC MOUNTING
• In the case of grinding or cutting discs with a thickness of less
than 3 mm, the nut of the outer flange (5) must be screwed
on flat on the disc side (fig. B).
• Press the spindle lock button (1).
• Insert the special key (supplied) into the holes of the outer
flange (5) (Fig. A).
• Turn the key - loosen and remove the outer flange (5).
• Place the disc so that it is pressed against the surface of the
inner flange (6).
• Screw on the outer flange (5) and lightly tighten with a special
spanner.
• Dismantling of the discs is carried out in the reverse order to
assembly. During assembly, the disc should be pressed
against the surface of the inner flange (6) and centrally seated
on its underside.
MOUNTING OF WORKING TOOLS WITH TAPPED HOLE
• Press the spindle lock button (1).
• Remove the previously mounted implement - if fitted.
• Remove both flanges - inner flange (6) and outer flange (5) -
before installation.
• Screw the threaded part of the working tool onto the spindle
and tighten slightly.
• Disassembly of threaded bore working tools is in reverse
order to assembly.
MOUNTING OF ANGLE GRINDER IN ANGLE GRINDER
STAND
• It is permissible to use the angle grinder in a dedicated tripod
for angle grinders, provided it is fitted correctly in accordance
with the tripod manufacturer's assembly instructions.
OPERATION / SETTINGS
• Check the condition of the grinding wheel before using it. Do
not use chipped, cracked or otherwise damaged grinding
wheels. A worn wheel or brush should be replaced
immediately with a new one before use. When you have
finished working, always switch off the grinder and wait until
the working tool has come to a complete standstill. Only then
11
- 1 pc.
- 1 pc.
- 1 pc.