Inhaltsverzeichnis
Werbung
067903-025 LX31/LX41/LX50
L
ABELS
These labels shall be present and in good condition before operating the work platform. Be sure to read,
understand and follow these labels when operating the work platform.
2
010076-001
4
060197-000
13
067480-000
Model______________
Serial number:___________
Machine weight _______kg
Mfg. date:_________
Maximum wheel load:________
Maximum allowable incline of machine when elevated:_____deg.
Occupants and equipment must not exceed the rated maximum
load:_____kg Maximum platform occupants: _____
Maximum allowable sIde force on platform:_____N
Maximum platform height:______m
Maximum platform reach:______m
Maximum allowable wind speed: ______m/s=Beaufort scale_____
Maximum hydraulic system pressure:_____bar
Maximum system voltage: _______Vdc
This machine is manufactured to comply with
Machinery directive 89-392/CEE
CAUTION: CONSULT OPERATOR'S MANUAL BEFORE USE.
061205-003
5
061205-003
13
067480-001
6
(Outrigger Units)
030768-002
USE OF THE AERIAL WORK PLATFORM: This aerial work platform is intended to lift persons and
their tools as well as the material used for the job. IT IS designed for repair and assembly jobs and
assignments at overhead workplaces (ceilings, cranes, roof structures, buildings etc.). All other uses
of the aerial work platform ARE PROHIBITED!
THIS AERIAL WORK PLATFORM IS NOT INSULATED! For this reason it is imperative to keep a safe
distance from live parts of electrical equipment!
ALL occupants must wear an approved fall restraint properly attached to a designated platform
7
064936-099
anchorage point. Attach only one fall restraint to each anchorage point.
Exceeding the specified permissible maximum load on the platform IS PROHIBITED!
The use and operation of the aerial work platform as a lifting tool or a crane (lifting of loads from
below upwards or from up high on down) IS PROHIBITED!
NEVER exceed 400 N of side force.
DISTRIBUTE all platform loads evenly on the platform.
NEVER operate the machine without first surveying the work area for surface hazards such as
holes, drop-offs, bumps, curbs, or debris; and avoiding them.
OPERATE machine only on surfaces capable of supporting wheel loads.
NEVER operate the machine when wind speeds exceed 28mph (12.5m/sec.=Beaufort scale 6).
IN CASE OF EMERGENCY push emergency stop button to deactivate all powered functions.
Climbing up the railing of the platform, standing on or stepping from the platform onto buildings, steel
or prefab concrete structures, etc., IS PROHIBITED!
Dismantling the swing gate or the liftable bar or other railing components IS PROHIBITED! Always make
certain that the swing gate or the liftable bar is closed and securely locked! IT IS PROHIBITED to keep
the swing gate or the liftable bar in an open position (e.g. held open with tie-straps) when the platform
is raised!
To extend the height or the range by placing of ladders, scaffolds or similar devices on the platform
IS PROHIBITED!
INSPECT the machine thoroughly for cracked welds, loose or missing hardware, hydraulic leaks,loose wire
connections, and damaged cables or hoses before using.
9
066552-000
VERIFY that all labels are in place and legible before using.
NEVER use a machine that is damaged, not functioning properly, or has damaged or missing labels.
IF ALARM SOUNDS while platform is elevated, STOP, carefully lower platform. Move machine to a firm,
level surface.
To bypass any safety equipment IS PROHIBITED and presents a danger for the persons on the aerial work
platform and in its working range.
NEVER charge batteries near sparks of open flame. Charging batteries emit explosive hydrogen gas.
14
067195-001
START CIRCUIT PROTECTION
If engine stops cranking while
starting, let machine sit for
11
067642-011
10-15 minutes before re-starting
(Outrigger Units:
15
067478-000
067642-004)
17
067822-000
21
063423-000
12
067481-001
Page 20
WARNING
TIPPING HAZARD
Check tire pressure daily.
Pressure must be
maintained at 50 P.S.I.
22
LX31/LX41:
40
LX31/LX41:
066558-001
066562-000
22
LX50:
40
LX50:
066562-003
005223-908
25
027898-000
41
066556-000
26
LX31: 066557-060
42
068639-000
26
LX41: 066557-057
26
LX50: 066557-054
43
066556-001
(Outrigger Units)
34 34
067822-001
44
066551-051
TIPPING HAZARD
If horn sounds continuously
lower platform and relevel.
45
066551-003
38
066561-001
(Outrigger Units)
Operator Manual
Labels
Bedien- und Anzeigeelemente
B
-
EDIEN
UND
4*
11
1. Lenkungsschalter
2. Sperrhebelschalter
3. Steuerhebel
4. Hilfsstützenschalter
5. Hilfsstützen-Anzeigeleuchten
6. Notausschalter
7. Heben/Fahren-Schalter
8. Geschwindigkeits-/Drehmoment-Wahlschalter
9. Fahrfunktionsleuchte
10. Schlüsselschalter
11. Vorglühknopf
12. Signalhorn
Hilfsstützen-Optionen
* Hilfsstützenschalter und Hilfsstützenlampen befinden sich
nur an Mascshinen, die mit Hilfsstützen ausgestattet sind.
** Eine Auswahl der Hilfsstützen ist nur bei Maschinen
möglich, die mit Hilfsstützen ausgestattet sind.
Betriebsanleitung
A
NZEIGEELEMENTE
Bedienelemente der Arbeitsbühne
1
1
2
2
3
4*
5*
5*
4
9
10
6
3
8
7**
12
9
1. Notaus
2. Arbeitsbühne/Fahrwerk-
Schalter
3. Hochfahrknopf
4. Absenkknopf
5. Startknopf
067903-025 LX31/LX41/LX50
Abbildung 30: Bedien- und Anzeigeelemente
Steuerpult des Fahrwerks
6
8
5
7
6. Vorglühknopf
7. Drosselklappenknopf
8. Abstellknopf
9. Niveausensor
Seite 5
Werbung
Kapitel
Inhaltsverzeichnis
