Environmental Protection; Technical Description - Eldom Invest Fv08046Tst Montage-, Betriebs- Und Wartungsanleitung

EN
WARNING!
Before installation and operation with the appliance, read carefully the present manual!
KEY REQUIREMENTS FOR SAFETY
Before starting the installation of your appliance and its operation it is
compulsory to read carefully the text of the instructions booklet. You must
respect its requirements and recommendations in order to help you use the
appliance, as well as the authorized persons who shall install and eventually
ATTENTION! Connection of the water heater to electrical installation should be performed
only by qualified persons. It must be performed in accordance with the instructions in
present guide. Moreover, it is mandatory to meet all requirements of the specific project for
installing, connecting the appliance to heat source and the use and management of the
entire system. Such project must be produced by a specialized company that carried out
design and eventually assembling operations.
ATTENTION! It is compulsory to connect the water heater to the protective earth circuit of
the building in which it is installed. This precaution is necessary because to the water heater
are fitted other electrical devices used for controlling the entire system.
WARNING! When using the appliance there is a risk of hot water scalding, especially when
the water in the water heater is heated to temperatures closer the thermostat higher limit.
WARNING! It is forbidden to allow circulation of the heating element through the heat
exchanger of the appliance before filling its water tank up with water!
WARNING! This appliance may be used by children of age over eight years old and
persons with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, where they are under supervision or instructed about the safe use of the
appliance and understand the dangers. Children must not be allowed to play with the unit! It
is absolutely forbidden that children undertake cleaning or servicing of this appliance!

ENVIRONMENTAL PROTECTION

This appliance is marked according the REGULATION concerning waste
electric and electronic equipment (WEEE). By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the accompanying documents
indicates that this appliance may not be treated as household waste.
Instead it should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. Disposal must be carried
out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of
this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

TECHNICAL DESCRIPTION

This water heater is intended for use only as part of a complete system built
to provide hot water for domestic consumers, consisting of the water heater,
additional external heat source and the requisite for the purpose protection
and control devices. Domestic water in the unit is heated by using the built-in
heat exchanger. As a coolant can be used a mixture of water and propylene
glycol in a ratio set by the system designer, as well as other water-based
coolant, containing the necessary anti-corrosion additives.
A schematic diagram for water heater connection is shown on Fig 1, while its
technical specifications - in the table.
repair the unit in case of malfunction. Compliance with the rules helps for
safety use of the appliance and is one of the warranty terms and conditions.
ATTENTION! Installation of the water heater and connection to the water
main system should be performed only by qualified persons. Installation of
safety and other components provided by the manufacturer is
COMPULSORY!
The appliances water containers are properly protected against corrosion
by using high quality enameled coating or are made of high-range alloy
chrome-nickel steel. Water tanks with enameled coating are equipped with a
built-in anode of special alloy, which by wearing provides additional
protection of the enameled coating.
The heated water should be correspond to the normative documents for
domestic water and, in particular: its chlorides composition should be less
than 250 mg/l and its electric conductivity should be more than 100 µS/cm,
while its pH within the limits of 6,5-9,5 for the water heaters with enameled
water tanks, and electric conductivity less than 200 µS/cm for the water
heaters with chrome-nickel steel water tanks. The water pressure in the
water supply system should be higher than 0.1 MPa and lower than 0.5
MPa. If the water pressure is higher than 0.5 MPa - please refer to the
instructions in the section for connection to the water supply network.
The built-in heat exchanger ensures rapid domestic water heating and
maintains the flow at the temperature set.
Within the device plastic cover is mounted a thermostat which can be used
to control the flow of coolant through the heat exchanger.
The outer casing of the appliances is made of epoxy-polymer coverage and
the heat insulation is made of CFC-free polyurethane foam.
INSTALLING THE WATER HEATER
The water heater can be installed only in normal fire safeguarded premises
and where temperature cannot fall under 0 °C.
The availability of a siphon on the installation for waste waters or another
system with the same purpose is necessary on the floor of the premises
because during normal usage of the water heater, water may happen to drop
7
EN