Technical Data; Noise/Vibration Information; Battery Charging - Bosch GST 12V-70 Originalbetriebsanleitung

OBJ_BUCH-2905-001.book Page 15 Monday, July 4, 2016 2:41 PM
21 Vacuum hose*
22 Splinter guard
23 Nose plastic sliding shoe
24 Screw
25 Scale for mitre angle
26 Locking screw for parallel guide*
27 Parallel guide with circle cutter*
28 Centring tip of the circle cutter*
29 Hex key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Cordless Jigsaw
Article number
Rated voltage
Stroke rate at no load n
0
Stroke
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
Bevel cuts (left/right), max.
Weight according to
EPTA-Procedure 01:2014
* depending on the battery pack being used
Battery
Permitted ambient temperature
– during charging
– during operation* and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined
according to EN 60745-2-11.
Typically the A-weighted noise levels of the
product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-11:
2
Cutting board: a =5.5 m/s , K=1.5 m/s
h
Cutting wooden beam: a =5.0 m/s
h
Bosch Power Tools
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
GST 12V-70
from the effects of vibration such as: maintain the tool and the
3 601 EA1 0..
accessories, keep the hands warm, organisation of work pat-
terns.
V= 12.0
-1
min 1500–2800
Assembly
mm 18
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
mm 70
and storage, remove the battery from the power tool.
mm 3
mm 3
There is danger of injury when unintentionally actuating
the On/Off switch.
° 45

Battery Charging

kg 1.5–1.7*
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
°C 0...+45
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
°C –20...+50
ducing its service life. Interrupting the charging procedure
GBA 10,8V...
does not damage the battery.
GBA 12V...
The lithium-ion battery is protected against deep discharging
AL 11.. CV
by the "Electronic Cell Protection (ECP)". When the battery is
GAL 12.. CV
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Observe the notes for disposal.
Battery Charge-control Indication
GST 12V-70
The three green LEDs of the battery charge-control indicator
5 show the charging status of the battery 1. The battery
charge-control indicator only illuminates for 5 seconds after
start-up.
LED
dB(A) 77
Continuous lighting 3 x green
dB(A) 88
Continuous lighting 2 x green
dB 3
Continuous lighting 1 x green
Flashing light 1 x green
Flashing light 3 x green
2
,
When no LED lights up after switching on, then the battery is
2 2
, K=1.5 m/s .
defective and must be replaced.
English | 15
Capacity
2/3
1/3
<1/3
Reserve
Empty
1 609 92A 3B5 | (4.7.16)