Product Description; Product Contents; Accessories; Assembly - Elero Rolmotion/D+ M-868 Bedienungsanleitung

Safety | Product description | Assembly
Symbol Signal
word
WARNING
CAUTION
Fig. 1 Notation for personal injuries
The table below describes the pictograms used in these
operating instructions to illustrate the hazard situation in
relation with the symbol for the hazard level.
Symbol Meaning
Danger caused by electrical voltage,
electric shock:
This symbol indicates dangers due to
electric current.
Fig. 2 Notation for specific danger
The table below defines the representation and description
of situations used in these operating instructions for situa-
tions in which damage can occur to the product or indicates
important facts, conditions, tips and information.
Symbol Signal
word
ATTENTION This symbol warns
IMPORTANT This symbol indicates
Fig. 3 Notation for damage to property and additional
information
The following example illustrates the basic structure of a
safety note:
SIGNAL WORD
Type and source of danger
Explanation of type and source of danger
►Measures to avoid the danger
Meaning
Warns about an accident
that may occur if the
instructions are not
followed, which can lead
to serious, possibly fatal,
irreversible injuries or
death.
Warns about an accident
that can occur if the
instructions are not
followed, which can
lead to slight, reversible
injuries.
Meaning
against possible damage
to property or equipment.
important facts and states
as well as referring to fur-
ther information in these
operating and assembly
instructions. It also refers
to certain additional in-
structions, which provide
additional information or
help you to carry out a
procedure more simply.
Symbol indicating suc-
cessful grounding with
protection class I ( Protec-
tive conductor system)
© elero GmbH
4

Product description

The RolMotion/D+ M-868 is a radio-controlled electronic
tubular drive for roller shutters. During operation it executes
radial movements.
‰ An elero assembly cable is not required to start up the
RolMotion/D+ 868. The elero assembly cable merely
serves to delete end positions or restore the delivery
condition. Commissioning of the RolMotion/D+ 868 to
configure various functions is performed with the elero
assembly cable or an elero radio transmitter.
‰ The RolMotion/D+ 868 requires fixed attachment points
at the top and bottom. A prerequisite is the use of rigid
shaft connectors and limit stops or angular bars/con-
cealed stops. There is a relief function for both anchor
points.
‰ If an obstacle is detected, the load is relieved by approx.
1 motor revolution (blind protection with free travel).
‰ If the same force cut-off occurs after three consecutive
uninterrupted movements, the end positions are set
(self-learning).
‰ Cyclical reference runs compensate for changes in the
winding behaviour of the roller shutter slats.
‰ In addition to the usual travel profile (standard mode
travel profile), the RolMotion/D+ M-868 drive also has a
reduced-speed travel profile (quiet mode travel profile).
‰ Slow travel when placing the roller shutter slats.
‰ Slow travel with timed and light-triggered release.
4.1

Product contents

Drive with safety instructions and operating instructions and
any additional components and accessories according to
the order confirmation or delivery note
4.2

Accessories

Connection and assembly cables, adapter sets, motor
bearings, radio sensors, radio transmitters, rigid shaft
connectors.
5

Assembly

WARNING
Important safety instructions
Observe all assembly instructions. Incorrect assembly can
lead to serious injuries.
►Commissioning of the RolMotion/D+ M-868 with elero
assembly cable for setting various functions.
►Before installation, all cables and components that are
not required and all facilities that are not needed for oper-
ation with a power drive are to be disabled.
►The required components are: drive, connection and
assembly cable, motor bearing, adapter sets, if neces-
sary rigid shaft connectors, sensors, control devices,
receivers.
►If components are not delivered with the drive, these can
be identified via our catalogue "Drives and control units
for intelligent building technology" in the relevant valid
version. Further details can be found on our website
under "Contact - dealer search" and "Contact - contact
persons for specialist companies".
►The rated torque and rated operating time must be suit-
able for the properties of the driven part (the blind).
►The coupling of the drive with the powered part is de-
scribed in the section "Mechanical fastening".
EN | 3