5.4.5 Changing/Deleting The End Positions; Programming The Transmitter; Programming The First Transmitter; Programming Additional Transmitters - Elero Rolmotion/D+ M-868 Bedienungsanleitung

Relief function | End position adjustment
Automatic teaching of end positions
1 Connect the electric power in accordance with
section 5.2.
2 Check for functioning: If necessary, change or swap
the assignment of the direction buttons for the operat-
ing switch/push button.
The drive switches off automatically when the (upper or
lower) limit stop is reached.
The teaching process is completed due to subsequent
travel of the shutter.

5.4.5 Changing/deleting the end positions

It is not possible to change or delete individual end posi-
tions. This is always done in pairs (upper and lower end
position simultaneously).
Changing/deleting the end positions
1
Switch on mains
2 Use the assembly cable to bring the blind to a central
position.
3
Press both direction keys [UP ▲]+[DOWN ▼] simulta-
neously.
The drive travels up and down briefly after about 5 seconds.
The end position settings have been deleted.
The end positions are configured again automatically as
described in section 5.4.4.
6

Programming the transmitter

Important
Precondition: The drive must be in radio operation mode.
►If the end positions have not been programmed, remove
the blind from the winding shaft.
6.1 Programming the first transmitter
Programming the (first) transmitter
Operating procedure
1
Switch the power off and
on again
2
Press the programming but-
ton [P] on the transmitter to
be programmed for approxi-
mately 1 second.
3 Immediately (maximum 1
second) after the start of
upward travel, press the
[UP ▲] button.
4
Immediately (maximum 1
second) after the start of
downward travel, press the
[DOWN ▼] button.
The (first) transmitter is now programmed.
6.2

Programming additional transmitters

Up to 16 transmitters can be programmed.
6 | EN
6.3
6.4
Result
The drive is in learning
mode for approximate-
ly 5 minutes.
The status display
lights up. The drive is
now in learning mode
(up/down travel) for
approximately
2 minutes.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
The status display
lights briefly. The drive
will stop.
© elero GmbH
Programming additional transmitters
Operating procedure
1
On an already programmed
transmitter, hold down the
buttons [UP ▲]+[DOWN ▼]
+ [P] (programming
button) simultaneously for
approximately 3 seconds.
(alternative to the previous
line)
Switch the power off and
on again
2
On the (additional) trans-
mitter to be programmed,
press the programming
button [P].
3
On the (additional) trans-
mitter to be programmed,
press the [UP ▲] button im-
mediately (within 1 second)
after the blind starts moving
upwards.
4
On the (additional) transmit-
ter to be programmed, press
the [DOWN ▼] button imme-
diately (within
1 second) after the blind
starts moving downwards.
The additional transmitter is programmed.
Stop the bidirectional radio programming mode:
Hold down the [STOP ■] button for at least 6 seconds until
the status display lights up (depends on transmitter).
Deleting the radio connection between
transmitters and receivers
Refer to the respective instructions for the transmitter.
Programming or deleting further blind
positions
• Intermediate position: Blind at any position between
upper and lower end position.
Defining the Approaching
interim position the intermedi-
in the receiver ate position
Prerequisite: The blind Prerequisite: The
is in the upper end intermediate position is
position. defined.
1. Press the [DOWN ▼] • Double click the
button until the [DOWN ▼] button
required intermediate (twice in quick
position is reached. succession):
2. Then press the Blind moves to the
[STOP ■] button. The saved intermediate
blind will stop. The position.
status LED lights up If no intermediate posi-
briefly. tion has been defined,
The intermediate posi- the blind moves to the
tion is now stored. lower end position.
If an intermediate
position is to be
controlled for several
receivers simultane-
ously, the receivers
must be programmed
on one channel (single
channel).
• Ventilation position:
Ventilation gaps for application of the roller shutters open
Result
The status display
lights up.
The drive is in learning
mode for approximate-
ly 5 minutes.
The drive is in learning
mode for approximate-
ly 5 minutes.
The status display lights
briefly. The drive is in
learning mode (up/
down travel) for approx-
imately 2 minutes.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
The status display
lights briefly. The drive
will stop.
Deleting the
intermediate
position
• Simultaneously
press and hold
the [DOWN ▼] +
[STOP ■] buttons for
approx. 3 seconds.
The intermediate
position is now deleted.
The status LED lights
up briefly.