Product Description; Product Contents; Accessories; Assembly - Elero Rolmotion M Nutzungsinformation

Safety | Product description | Assembly
Symbol Signal
word
WARNING
CAUTION
Fig. 1 Notation for personal injuries
The table below describes the pictograms used in these
operating instructions to illustrate the hazard situation in
relation with the symbol for the hazard level.
Symbol Meaning
Danger caused by electrical voltage,
electric shock:
This symbol indicates dangers due to
electric current.
Fig. 2 Notation for specific danger
The table below defines the representation and description
of situations used in these operating instructions for
situations in which damage can occur to the product or
indicates important facts, conditions, tips and information.
Symbol Signal word Meaning
ATTENTION This symbol warns
IMPORTANT This symbol indicates
Fig. 3 Notation for damage to property and additional
information
The following example illustrates the basic structure of a
safety note:
SIGNAL WORD
Type and source of danger
Explanation of type and source of danger
►Measures to avoid the danger
Meaning
Warns about an accident
that may occur if the
instructions are not
followed, which can lead
to serious, possibly fatal,
irreversible injuries or
death.
Warns about an accident
that can occur if the
instructions are not
followed, which can
lead to slight, reversible
injuries.
against possible damage
to property or equipment.
important facts and states
as well as referring to
further information in
these operating and
assembly instructions.
It also refers to certain
additional instructions,
which provide additional
information or help you
to carry out a procedure
more simply.
Symbol indicating
successful grounding
with protection class I
(Protective conductor
system)
© elero GmbH
4

Product description

The RolMotion M is an electromechanical tubular drive for
roller shutters, interior roller shutters and insect screens.
During operation it executes radial movements.
‰ Commissioning of the RolMotion M with elero assembly
cable or radio transmitter for setting various functions.
‰ Blind protection with free travel (torque limiting).
‰ Relief function for the blind (blind protection).
‰ Cyclical reference runs compensate for changes in the
winding behaviour of the roller blind slats.
‰ In addition to the usual travel profile (travel profile
standard), the RolMotion M drive also has a reduced-
speed travel profile (motion travel profile).
‰ Slow travel when placing the roller blind slats.
4.1

Product contents

Drive with safety instructions and operating instructions and
any additional components and accessories according to
the order confirmation or delivery note.
4.2

Accessories

Connection and assembly cable, adapter sets, motor
bearing, ProLine control units, sensors, receivers.
5

Assembly

WARNING
Important safety instructions
Observe all assembly instructions. Incorrect assembly can
lead to serious injuries.
►Commissioning of the RolMotion M with elero assembly
cable for setting various functions.
►Before installation, all cables and components that are
not required and all facilities that are not needed for
operation with a power drive are to be disabled.
►The required components are: drive, connection
and assembly cable, motor bearing, adapter sets, if
necessary rigid shaft connectors, sensors, control
devices, receivers.
►If components are not delivered with the drive, these can
be identified via our catalogue "Drives and control units
for intelligent building technology" in the relevant valid
version. Further details can be found on our website
under "Contact - dealer search" and "Contact - contact
persons for specialist companies".
►The rated torque and rated operating time must be
suitable for the properties of the driven part (the blind).
►The coupling of the drive with the powered part is
described in the section "Mechanical fastening".
CAUTION
Risk of injuries due to hot surfaces.
The drive will heat up during operation, the drive casing
can become hot. Skin burns are possible.
►Wear personal protection equipment (protective gloves).
Triggered by a possible material fault, knocks or impact
injuries may arise due to a gear fracture, burring fracture or
a coupling defect.
►Suitable materials have been used for the engineering
design and random sample testing by means of a double
load test has been performed in accordance with
DIN EN 60335-2-97.
EN | 3