elero RolTop/D+ Nutzungsinformation Seite 17

Troubleshooting | EC Declaration of Conformity
Changing / Deleting the end positions
The deletion of the setting of end position is completed.
The end positions can be programmed again.
Changing / deleting the limit positions
Method 2 only for types RolTop/D+
Move the blind with built-in drive to a centre position.
1
Move both direction buttons to the OFF position and
wait 3 seconds.
2 Press the [UP ▲] button 5 times in quick succession;
wait for the blind to move briefly in between.
3 Press the [DOWN ▼] button 5 times in quick suc-
cession; wait for the blind to move briefly in between.
Press and hold for at least 1 second on the fifth time
and there is no reaction.
The deletion of the end position setting is complete.
The end positions can be programmed again.
5.6 Specifications
A summary of the main technical parameters, see the sepa-
rate overview "Technical Specifications".
6 Troubleshooting
Problem / Possible
Error cause
• Drive does not • Drive has
learn any end
positions
• Drive stops • Sluggish shut-
after a short
ride
• Undersized
• Drive not • No mains volt-
responding
• Thermostat
• Drive starts • Connection
only in one
direction
• Drive does not • Drive has not
stop due to
obstacle
Fig. 7 Error search at the RolTop/D+
7 Repair
The RolTop/D+ is maintenance free.
8 Repair
If you have any questions, please refer to your specialised
company. Please always state the following information:
• Item number and item designation on the nameplate
• Error type
Cure
Remedy
• Move shutter
already been to the central
programmed to position, bring
end position the drive to
end position
deletion in the
delivery status
• Check for ease
ter of hanging or
selection of the
drive
drive
• Check mains
age voltage
• Allow drive to
has tripped cool
• Check connec-
error tion
• Drive must be
saved any cut- moved from
off values end stop to
end stop at
least 2 times
without stop-
ping
• Previous and unusual events
• Surrounding circumstances
• Own assumption
9 Service/manufacturer's address
After installing the drive, the R+S mechatronics technician
(roller shutter and sun protection mechatronics technician)
must note the installed type of drive and the installation
location in the installation and operating instructions.
Drive designation
____________________
____________________
If malfunctions occur despite proper handling or if the unit
has been damaged, contact your contract partner.
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach
Deutschland / Germany
Should you require a point of contact for outside of Ger-
many, please visit our website.
10 Disposal / scrapping
Dispose of the packaging according to current regulations.
Dispose the product after previous use in accordance with
applicable regulations.
Scrapping
During the scrapping of the product, the international,
national and regional-specific laws and regulations are to be
complied with.
Please make sure to consider material recyclability, ease of
dismantling, and separability of materials and components
as well as environmental and health hazards during recy-
cling and disposal.
Groups of materials such as plastics and metals of various
kinds are sorted for recycling and disposal process.
Dispose electrical and electronic components
Disposal and recycling of electric and electronic compo-
nents must comply with the applicable national laws and
regulations.
11 EC Declaration of Conformity
elero GmbH hereby declares that this product corresponds
to the applicable directives. The complete declaration of
conformity can be found under
www.elero.com/en/downloads-service/
12 Energy efficiency
The drive remains below the legally required consumption
values of the European Ecodesign Directive 2023/826.
After the main function 'raising' or 'lowering' (active mode)
has ended and the roller shutter switch is left in the UP or
DOWN position, the power consumption is less than 0.3 W
(standby mode). There is no power consumption when the
switch is in the 'OFF' position.
© elero GmbH
Installation location
(e.g. living room window 2)
_________________________
_________________________
Phone: +49 7021 9539-0
Fax: +49 7021 9539-212
info.elero@niceforyou.com
www.elero.com
EN | 7