Operation - Conrad RSLT Bedienanleitung

• Briefl y press the "TEMP" button; in the display, "OFF" appears to the left of the temperature value.
• Set the turn-off temperature with the buttons "ALL-ON" or "ALL-OFF" (if the receiver should be switched
on, it will be switched off when the temperature climbs above this value).
☞
If the temperature-dependent switching function is enabled, the frost protection function
(> +4°C) can also be activated by pressing "DEL" (a star symbol appears on the LCD screen).

Operation

a) Recognition of a radio receiver with the radio remote control
• Choose the desired switch group I, II, III, or IV with the sliding switch (4).
• Set the radio receiver (e.g. a radio built-in switch, a radio switch socket, etc.) in Learn Mode. On this, see
the operating instructions of the radio receiver (in most cases, the button on the receiver is to be pressed
and held for more than 3 seconds, until an LED on the receiver begins to blink).
• Press and hold the "ON" button of one of the four channels on the radio remote control until the LED on the
receiver stops blinking and instead remains lit (about 3 seconds). The user connected to the radio receiver
is switched on. Now release the button; the radio receiver is recognized on the desired switch channel.
☞
At every receiver of the RSL system, up to 10 different remote controls can be recognized.
b) Deleting already recognized radio receivers from the radio remote control
• Choose the switch group I, II, III, or IV, at which the receiver is recognized, with the sliding switch (4).
• Set the radio receiver (e.g. a radio built-in switch, a radio switch socket, etc.) in Learn Mode. On this, see
the operating instructions of the radio receiver (in most cases, the button on the receiver is to be pressed
and held for more than 3 seconds, until an LED on the receiver begins to blink).
☞
You can also switch the (already recognized) receiver that you want to delete into Learn Mode
by pressing the "ON" and "OFF" buttons of the corresponding channel on the remote control at
the same time and holding them for at least 3 seconds.
You can use this method, for example, if a radio built-in switch is inaccessibly mounted and you
cannot press its buttons.
• Press and hold the "OFF" button on the radio remote control that corresponds to the channel on which the
receiver is recognized until the LED on the receiver stops blinking and instead goes out (about 3 seconds).
The user connected to the radio receiver is switched off.
The receiver's recognition of the corresponding channel of the remote control is deleted; the receiver no
longer responds to the remote control.
c) Dimmer function of the radio remote control
☞
The dimmer function of the radio remote control is naturally possible only when the radio re-
ceiver has an integrated dimmer.
• Choose the desired switch group I, II, III, or IV with the sliding switch (4).
• Turn the receiver on by pressing the ON button for the corresponding switching channel briefl y . The lights
connected to the receiver are switched on with the previously available brightness setting.
• Briefl y press the "ON" button for the corresponding switching channel again.
Thereupon the dimmer function of the corresponding receiver starts. The brightness of a light connected
to the receiver now changes progressively.
• To stop the dimmer function (and thus to set the brightness of a light connected to the receiver), briefl y
press the "ON" button of the corresponding switching channel once more.
d) Switching individual receivers on/off
• Choose the desired switch group I, II, III, or IV with the sliding switch (4).
• Briefl y press the "ON" button of the corresponding switching channel to switch on the radio receiver and
the users connected to it.
• Briefl y press the "OFF" button of the corresponding switching channel to switch off the radio receiver and
the users connected to it.
e) Switching all receivers on/off
With the "ALL ON" (3) or "ALL OFF" (11) buttons, all receivers recognized by the remote can be switched on
or off. With this function, you can, for example, switch all the lights in the house on or off.
• "ALL-ON" button (3): Switch on all receivers
• "ALL-OFF" button (11): Switch off all receivers
Use weekly switching program
Move the sliding switch (4) to Switch Group IV, see image right.
Then press the "PROG" button (6). The display shows "PROG". The weekly
switching program function is activated (only for receivers recognized in the switch
group IV on Channel 2).
To deactivate the weekly switching program function, briefl y press the "PROG" button (6); the "PROG" indica-
tor disappears from the display.
Using Countdown Mode
Move the sliding switch (4) to Switch Group IV, see image right.
Briefl y press the "CD" button (7). The current countdown time appears on the dis-
play. Start the countdown by briefl y pressing the "CD" button again.
The "CD" indicator appears in the display; the countdown runs (only for receivers recognized in the switch
group IV on Channel 1). The remaining time is displayed.
To deactivate the countdown mode, briefl y press the "CD" button (7); the "CD" indicator disappears from
the display.
Using random mode
Move the sliding switch (4) to Switch Group IV, see image right.
Briefl y press the "RND" button (8). The display shows "RND". The randomiza-
tion function is activated (only for receivers recognized in the switch group IV on
Channel 3).
To deactivate the randomization function, briefl y press the "RND" button (8); the "RND" indicator disappears
from the display.
Using temperature-dependent switching function
Move the sliding switch (4) to Switch Group IV, see image right.
Briefl y press the "TEMP" button (9). The display shows "TEMP". The temperature-
dependent switching function is activated (only for receivers recognized in the
switch group IV on Channel 4).
To deactivate, press the "TEMP" button (9) again; the "TEMP" indicator disappears.
Maintenance and Care
The product does not require any maintenance and should never be opened or disassembled for any reason.
Only clean the product with a soft, clean, dry cloth. Never use aggressive cleaning agents or chemical solu-
tions since these might damage the surface of the casing or impair the operation.
Do not press too hard on the display. This not only causes scratches but also can damage the display; loss
of warranty!
Information about the range
The radio LCD remote control has a range of up to 50 m.
☞
This value, however, is the so-called "open space range" (the range the transmitter and receiver
are visible to each other, without disturbing infl uences).
In practical operation, however, there are walls, the ceilings of rooms etc. between the transmit-
ter and the receiver which reduce the range correspondingly.
Due to the different infl uences on the radio transmission, no specifi c range can be guaranteed.
However, trouble-free operation is usually possible in a detached house.
The range can sometimes be limited considerably by:
• Walls, reinforced concrete ceilings
• Coated/vapour-deposited, metallised insulating glass panes
• Proximity to metal & conducting objects (e.g. radiators)
• Proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-controlled
headphones, radio-controlled speakers, radio-controlled weather stations, baby phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• proximity to badly shielded or uncovered computers in use or other electrical appliances
Disposal
a) In general
Dispose of an unserviceable product in accordance with the relevant statutory regulations.
Remove any inserted battery and dispose of it separately from the product.
b) Disposal of used batteries/rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all used batteries/rechargeable bat-
teries; disposal of them in the household waste is prohibited!
Contaminated batteries/rechargeable batteries are labelled with these symbols to indicate that
disposal in the domestic waste is forbidden. The symbols for the relevant heavy metals are: Cd
= Cadmium, Hg = Mercury, Pb = Lead.
You can return used (rechargeable) batteries free of charge at the offi cial collection points in
your municipality, our stores, or where ever (rechargeable) batteries are sold!
You thus fulfi l the legal requirements and make your contribution to protecting the environment!
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product con-
forms to the fundamental requirements and the other relevant regulations of the directive 1999/5/EC.
☞
The Declaration of Conformity for this product can be found at www.conrad.com.
Technical Data
Power supply ...............................2 batteries of type AAA/Micro
Transmission frequency...............433 MHz
Transmission range .....................Max. 50 m (see chapter "Range")
Ambient temperature ...................0 °C to +35 °C
Dimensions (LxWxH) ...................151 x 54 x 23 mm
Weight .........................................approx. 86 g (without batteries)
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.