Temperature Limits; Combinations Of Cutting Attachments And Deflectors - Stihl Fsa 110.0 R Gebrauchsanleitung

22 Combinations of Cutting Attachments and Deflectors

– Data connection: Bluetooth
mobile appliance must be compatible with
®
Bluetooth Low Energy 5.0 and support
Generic Access Profile (GAP).
– Frequency band: ISM band 2.4 GHz
– Maximum RF power transmitted: 1 mW
– Signal range: approx. 10 m. The signal
strength depends on the ambient conditions
and the mobile terminal. Signal range can
vary greatly depending on local conditions,
including the receiver. The range may be
perceptibly reduced inside enclosed rooms
and through metal barriers (such as walls,
shelves or cases).
– Mobile appliance operating system require‐
ments: Android or iOS (current version or
higher)
21.3

Temperature limits

WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain environmental conditions, it may catch fire
or explode. This may result in serious injury to
people and damage to property.
► Do not charge the battery below -20°C or
above 50°C.
► Do not use the brushcutter or battery below
-20°C or above 50°C.
► Do not store the brushcutter or battery
below -20°C or above +70°C.
21.4 Recommended temperature
ranges
For optimum performance of the brushcutter and
battery, note the following temperature ranges:
– Charging: 5°C to 40°C
– Use: - 10 °C to + 40 °C
– Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be restricted.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
21.5 Sound and vibration values
The K-value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K value for the vibration level is
2 m/s².
0458-064-9601-A
®
5.1. The
STIHL recommends wearing hearing protection.
Use with a mowing head except PolyCut 12-2
– Sound pressure level L
ance with IEC 62841-4-4: 76 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 91 dB(A)
– Vibration value a
hv
with IEC 62841-4-4
– Control handle: 2.0 m/s²
– Loop handle: 4.9 m/s²
Use with a PolyCut 12-2 mowing head
– Sound pressure level L
ance with IEC 62841-4-4: 79 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 91 dB(A)
– Vibration value a
hv
with IEC 62841-4-4
– Control handle: 2.0 m/s²
– Loop handle: 3.8 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
load. The actual vibration load has to be estima‐
ted. The times can be taken into account in the
estimate when the electric power tool is switched
off and also when it is switched on but running
without any load.
For information on compliance with the Physical
Agents (Vibration) Directive 2002/44/EC, see
www.stihl.com/vib.
21.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
22 Combinations of Cutting
Attachments and Deflec‐
tors
22.1 STIHL FSA 110 R Brushcutter
The following mowing heads may be mounted
with the deflector:
– STIHL AutoCut C 12-2 mowing head:
English
measured in accord‐
pA
measured in accord‐
wA
measured in accordance
measured in accord‐
pA
measured in accord‐
wA
measured in accordance
39