Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
resume cleaning where it left off until the entire surface has been mapped. The robot
vacuum cleaner is constantly mapping, so it adapts in an individual and personalised way
to the particularities of each home and constantly improves its map.
-
The robot will return to the charging base to clean the mops and moisten them again to
continue cleaning, according to the frequency selected in the application.
Information about the charging base
-
The charging base includes the charging function, mop cleaning and dirt tank emptying.
After cleaning, the robot will automatically return to the charging base to recharge the
battery, empty the dirt tank, clean and dry the mops.
-
During cleaning, the robot will return to the charging base to clean the mops and moisten
them again to continue cleaning where it left off, depending on the frequency selected in
the app.
-
The base will perform the self-emptying function according to the emptying frequency
value selected on the app.
-
In addition, it is possible to force the emptying of the dirt tank from the robot vacuum
cleaner by pressing the Back Home button or from the app.
-
When the robot vacuum cleaner reaches the charging base it will beep once, indicating that
it has made good contact with the charging terminals of the base.
-
The base will then clean the mops and collect the dirty water generated. After cleaning and
dirty water collection, the base will activate the mop drying function.
-
If the indicator light on the charging base is red, it may indicate that the dirt bag is not
attached or is full, the clean-water tank is empty or the dirty water tank is full.
-
If so, fit or replace the bag, fill the clean-water tank or empty the dirty water tank.
3. OPERATION
Robot vacuum cleaner's buttons
Auto Mode
-
Press the Start/Pause button on the robot vacuum cleaner or from the app for the robot
to automatically start cleaning in Edge mode and perform a cleaning cycle in an orderly
zig-zag pattern, while recognising which areas it has cleaned and which it hasn't. The
robot vacuum cleaner will automatically plan the cleaning route during cleaning.
-
The robot will return to the charging base to clean the mops and moisten them again to
continue cleaning, according to the frequency selected in the application.
-
If you control the robot vacuum cleaner manually during this mode, the robot will
recalculate the route, so it may pass through already cleaned areas. To ensure efficient
cleaning, do not operate the robot vacuum cleaner manually during automatic cleaning.
-
Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle,
72
CONGA 13090 SPIN REVOLUTION HOME&WASH
the robot vacuum cleaner will smartly return to the charging base automatically and once
fully charged, it will resume the cleaning process from the same point.
-
During cleaning, the robot vacuum cleaner will stop briefly to evaluate the area and
calculate the cleaning route (this stop will vary depending on the house conditions).
Back Home mode
-
Press the Back Home button on the robot vacuum cleaner or from the app to send the robot
vacuum cleaner to the charging base.
-
This mode can be activated during any cleaning cycle.
-
The robot vacuum cleaner will take the shortest route back to the charging base thanks to
its map-memorisation feature and the smart back-home function.
-
Upon completing a cleaning cycle or when the battery is low, thanks to its TotalSurface
2.0 technology, the robot vacuum cleaner will automatically return to the charging base to
avoid running out of battery. Once the robot has recharged, it will resume cleaning from
the point it has stopped.
Note:
If there is no good access to the charging base, the robot vacuum cleaner will not be able to
return to it. If this happens, manually place it in the self-emptying base.
Functions
Pause
While the robot vacuum cleaner is operating, press the Start/Pause button on the robot
vacuum cleaner or select it in the app to pause the cleaning process. Press the Start/Pause
button on the robot vacuum cleaner or on the app to resume the cleaning process.
Standby
The robot vacuum cleaner will automatically enter standby mode after 10 minutes of inactivity.
Press the Start/Pause button on the robot vacuum cleaner or in the app to activate it again.
Cleaning modes
-
The robot vacuum cleaner includes different modes and functions that can be toggled
from the app.
-
In addition, in every one of the cleaning modes on the app, you will be able to select the
Turbo mode on carpets, which activates the maximum suction power when the robot
vacuum cleaner detects a carpet.
-
Please note that the robot will stop the rotary movement of the mops when it detects
the carpet, but if the mops are wet it may dampen the carpet. To avoid this, from the
application you can indicate restricted areas in the areas where the carpets are in your
home, or directly from the application indicate that the robot does not climb on the carpet
when it detects it.
ENGLISH
CONGA 13090 SPIN REVOLUTION HOME&WASH
73
Werbung
