Parkside Performance PABSP 20 LI C3 Kurzanleitung Seite 18

˜ LED work light
This product is equipped with a LED work light
the immediate working area to improve visibility in poorly lit
areas .
The LED work light lights up automatically as soon as
[ 11 ]
the product is switched on .
NOTE
The LED work light
u 11 ] [
approx . 10 seconds after switching off the product .
˜ Working instructions
Torque
Smaller screws/bits can be damaged if you set the torque
or rotational speed too high .
Hard screw joints (in metal)
Particularly high torque occurs, for example in metal screw
joints made using drive sockets . Select a low rotational
speed .
Soft screw joints (e.g. in soft wood)
Again, use a low rotational speed, e .g . to avoid damaging
the surface of the wood upon contact with the screw head .
Use a countersink .
Drilling in wood, metal and other materials
Use a high speed for drill bits with small diameter and a
low speed for drill bits with large diameter .
Select a low speed for hard materials and a high speed for
soft materials .
Secure or fasten the workpiece in a clamp or vice (if
possible) .
Mark the spot where you want to drill using a centre punch
or nail . Select a low rotational speed when starting .
Pull the rotating drill bit from the hole repeatedly to remove
dust and chips and clear the hole .
Drilling in metal
Use a metal drill (HSS) . For optimum results, cool the
drill bit with cooling lubricant (cutting oil) . Metal drill bits
can also be used to drill into plastics . Start with a 3 mm
diameter drill bit and then increase the size until the desired
hole diameter is achieved .
Drilling in wood
Use a wood drill with a lathe centre .
Deep holes: Use an auger bit .
Large-diameter holes: Use a Forstner bit .
Small screws can be screwed directly into soft wood .
18 GB
to illuminate
[ 11 ]
stays on for an additional
Belt clip
(Fig . J)
m
CAUTION! RISK OF INJURY!
Before hanging the product in the belt: Push the rotation
u
direction switch to the centre position (lock) .
[ 5 ]
This prevents the product from being switched on
accidentally .
NOTE
The belt clip allows the tool to be hooked on belt
u [ 9 ]
or pocket .
The belt clip is not assembled upon delivery .
u
The belt clip can be mounted on either side of a belt .
u
For the assembly of the belt clip a cross tip screwdriver
u
is required .
1 . Use a cross tip screwdriver to loosen the screw of the belt
clip .
9 ] [
2 . Insert the belt clip on either side of the product .
3 . Use a cross tip screwdriver to tighten the screw .
˜ Connecting the product to the
PARKSIDE app
˜ Activate/deactivate the Bluetooth
function on the battery
1 . Press and hold the
for 3 seconds to activate the Bluetooth
orange LED of the charging level LEDs
Bluetooth function is enabled .
®
2 . Release the button
3 . Press and hold the
for 10 seconds to deactivate the Bluetooth
orange LED of the charging level LEDs
function is deactivated . In the PARKSIDE app
Bluetooth
®
the product is shown as offline .
˜ Connecting the product to the
PARKSIDE app
NOTE
The product can only be connected to the PARKSIDE
u
app if the battery pack
Only Smart Performance rechargeable batteries can be
u
connected to the PARKSIDE app .
1 . Press and hold the
for 3 seconds to activate the Bluetooth
2 . Enable the Bluetooth function on your smartphone .
®
Open the PARKSIDE app .
3 .
®
button on the battery pack
13 ] [
function . The
®
lights up . The
[ 14 ]
.
13 ] [
button on the battery pack
13 ] [
function . The
®
goes off . The
14 ] [
is inserted in the product .
10 ] [
button on the battery pack
[ 13 ]
function .
®
10 ] [
10 ] [
10 ] [