Trial Run; Operation; Torque Control; Speed Control - Parkside Performance Pabsp 20 Li C3 Kurzanleitung

This product is equipped with an automatic spindle lock to open
or close the chuck with the chuck ring
1 ] [
Open the chuck : Turn the chuck ring
[ 1 ]
clockwise direction (Fig . E) .
Insert a suitable accessory tool into the chuck
as required .
Close the chuck : Hold the accessory tool in position .
1 ] [
Turn the chuck ring in a clockwise direction .
[ 2 ]
NOTE
This product is equipped with a Röhm drill chuck with an
u
anti-lock function .
If you attempt to open the fully opened chuck
u
the anti-lock function will be activated to protect the
chuck .
When the anti-lock function is activated, the chuck
u
cannot be closed by turning the chuck ring
clockwise direction . A ratcheting sound will be produced
when you attempt to close the chuck .
Deactivating the chuck's
u
the chuck ring in a clockwise direction by a certain
2 ] [
extent . Then, turn the chuck ring
quickly in a counter-clockwise direction .
Repeat this action if the anti-lock function is still active .
When the anti-lock function is deactivated, you should
be able to close the chuck
˜ Trial run
NOTE
Always carry out a no-load trial run before starting work
u
and after every accessory tool replacement . Switch
the product off immediately if the accessory tool is not
running smoothly, if considerable vibration occurs or if
you hear abnormal noises .
Before operating the product, check whether the accessory
tool is correctly positioned, i .e . centred in the chuck
Screw bits are labelled according to their dimensions and
their shape . If you are uncertain, always check whether the
bit fits tightly in the screw head without any free play .
˜ Operation
˜ Gear selection
m
ATTENTION! RISK OF PRODUCT DAMAGE!
Do not operate the gear selector
product has come to a standstill .
Change the gear by sliding the gear selector
or backwards (fig . F) .
.
[ 2 ]
in a counter-
2 ] [
as deep
[ 1 ]
further,
[ 1 ]
1 ] [
in a
[ 2 ]
anti-lock function: Turn
1 ] [
suddenly and
[ 2 ]
without ratcheting sounds .
[ 1 ]
.
1 ] [
until the
[ 4 ]
forwards
4 ] [
1 gear:
st
Suitable for:
Speed:
Torque:
2 gear:
nd
Suitable for:
Speed:
Torque:
˜ Setting the rotating direction
m
ATTENTION! RISK OF PRODUCT DAMAGE!
Do not operate the rotation direction switch
until the product has come to a standstill .
Change the direction of rotation by pressing the rotation
direction switch towards the left or right (fig . G) .
[ 5 ]
When the rotation direction switch
position, the on/off switch
˜ Torque control
This product is equipped with a torque control that disengages
the spindle when a predefined torque is exceeded .
The torque can be adjusted by turning the torque sleeve
(fig . H) .
Small screws or soft materials: Select a low level .
Large screws, hard materials or removing screws: Select a
high level .
For drilling operation: Turn the torque sleeve
position .
˜ Switching on and off
NOTE
The on/off switch cannot be locked .
[ 6 ]
u
Switching on: Press and hold the on/off switch
Regulate the speed as required (see "Speed control")
(fig . I) .
Switching off: Release the on/off switch
˜ Speed control
By using the on/off switch
control the speed:
Pressure
Gentle pressure:
Greater pressure:
Screwing
Low
High
Drilling
High
Low
[ 5 ]
is in the middle
5 ] [
is locked .
[ 6 ]
to the
3 ] [
.
[ 6 ]
.
6 ] [
, you can progressively
[ 6 ]
Speed
Lower speed
Higher speed
GB 17
3 ] [