Connections - Omnitronic BPM-6 Beatcounter Bedienungsanleitung

4. CONNECTIONS

SIX CUE POINT MEMORY
SAMPLE MEMORY CUE CUE 1 CUE 2 CUE 3 CUE 4
OPEN/CLOSE PROG
1
SGL TIME
Dual CD-Player PITCH BEND
REV- FWD+
CDP-820
TRACK
SEAMLESS
LOOP
CUE IN/R. CUE OUT/EXIT
JOG/SEARCH SHUTTLE/SCAN
Dual CD-Player
CDP-820
COMPACT
DIGITAL AUDIO
1 BIT 8 TIMES OVERSAMPLING D/A CONVERTER COMPACT DISC PLAYER
1
L
R
OUT IN OUT
CH 6 CH 5
• Install the device on a plane surface.
• Make sure that the power switch is set to OFF. Before you connect the devices, all units have to be
switched off.
• In order to obtain highest sound quality, only use high-quality cables for connecting the devices. Make sure
that the cables are properly fixed.
• The Beatcounter has to be connected between the output of the signal source (CD-player or turntable) and
the mixer input.
• Via the PHONO/CD-selector on the rearpanel, you can determine whether you want to connect a truntable
(PHONO) or a CD-player (AUX) to the respective channel (only CH-1, CH-2 and CH-3).
• You can connect up to 6 CD-players using the In-sockets CH-1, CH-2, CH-3, CH-4, CH-5 and CH-6 on the
rearpanel after you switched the PHONO/CD selectors to CD.
• You can connect up to 3 turntables using the In-sockets CH-1, CH-2 and CH-3 on the rearpanel after you
switched the PHONO/CD selectors to PHONO.
• Only connect the Out-sockets at the BPM-6 with the respective LINE-input socket at the mixer.
• Connect the connection cable of the power-unit with the AC IN-socket. Plug the power unit into your outlet.
MEMORY
CUE 5 CUE 6 CUE CUE 1 CUE 2 CUE 3 CUE 4 CUE 5 CUE 6
BEAT
OPEN/CLOSE PROG
COUNTER COUNTER
PITCH PITCH
8%, 12%, 16% BPM BPM 2 8%, 12%, 16%
SGL TIME
RELAY
1 2 3
PITCH BEND
REV- FWD+
PITCH 4 5 6 PITCH
0 0
TRACK
+10
+10
7 8 9
SEAMLESS
LOOP
RELOOP CUE IN/R. CUE OUT/EXIT RELOOP
+ 0 +
DISC 1 DISC 2
12 x 2 sec. sampler
JOG/SEARCH SHUTTLE/SCAN
COMPACT
OPEN/CLOSE
1 2
DIGITAL AUDIO
1 BIT 8 TIMES OVERSAMPLING D/A CONVERTER COMPACT DISC PLAYER
2
POWER
IN OUT IN OUT IN OUT
CH 4 CH 3
CAUTION
Read manual before use. To prevent electrical fire and shock hazard,
do not expose this appliance to moisture. Risk of electric shock!
Do not open! There are no serviceable parts inside the device.
Typ/Type: OMNITRONIC PM-660
Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen.
Spannungsversorgung/ Gefahr! Gerät nicht öffnen!
sich keine zu wartenden Teile.
Power supply: 15 V AC, 1 A ~
Lire le mode d'emploi avant l'utilisation. Afin de prévenir tous risques
Gesamtanschlusswert/Power d'électrocution et de court-circuits, ne pas exposer à l'humidité.
Attention! Ne pas ouvrir le boîtier!
consumption: 15 VA
ne contient pas de parties nécessitant un entretien.
MASTER BOOTH REC
L
R
OUTPUT
15 V AC
POWER
START/STOP
33
INPUT
L PHONO PHONO
R
CD
IN OUT IN
CH 2 CH 1 CH 1 CH 2
®
OMNITRONIC
www.omnitronic.com
OMNITRONIC SHOWEQUIPMENT GmbH, GERMANY
MIC 3 MIC 2 MIC 1
Im Geräteinneren befinden
L'intérieur de l'appareil
LINE 5 LINE 4
LINE 3 PHONO 3 LINE 2 PHONO 2 LINE 1
CH-4 CH-3 CH-2
13/25
PITCH
CORRECTION
DSP inside
OMNITRONIC
Professional High Torque Direct-Drive Turntable 10 % QUARTZ
PITCH +/-
DD-5220 DSP 20 % LOCK
45
Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen! Niemals
das Gerät öffnen! Im Geräteinnern befinden sich keine zu wartenden
Teile. Wartungs- und Servicearbeiten nur durch autorisierten Fachhandel!
Read user manual before use. Keep away from moisture! Never open the
housing! There are no serviceable parts inside the device. Maintenance
and service operations only by authorized dealers.
Typ/Type: BPM-6
Spannungsversorgung/Power supply: 12 V AC, 1 A
Gesamtanschlusswert/Power consumption: 12 W
OMNITRONIC SHOWEQUIPMENT GmbH, GERMANY
OMNITRONIC
CD
www.omnitronic.com
MADE IN CHINA MADE IN CHINA
CH 3
GND
PHONO 1
L
R
CH-1
10453020_V_1_0.DOC
AC IN
®
12V/1A