Herunterladen Diese Seite drucken

Scheppach BC-RHD230-X Originalbetriebsanleitung Seite 23

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
WARNING
This power tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain circumstances. In order
to prevent the risk of serious or deadly injuries, we rec-
ommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the power tool.
WARNING
In case of extended working periods, the operating per-
sonnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
Raynaud's syndrome is a vascular disease that causes
the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear ex-
tremely pale. The frequent use of vibrating products can
cause nerve damage in people whose circulation is im-
paired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working im-
mediately and seek medical advice.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
WARNING
Follow the safety and charging instructions
and correct usage given in the instruction
manual of your 20V IXES Series battery and
charger.
A
detailed
charging process and further information are
provided in this separate manual.
7
Unpacking
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the trans-
port company that delivered the Product. Later claims
will not be recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
description
of
the
www.scheppach.com
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
8
Before commissioning
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
8.1
Inserting/removing the battery (11)
in the battery mount (10) (Fig. 2)
Note:
If necessary, swivel the additional handle (13) before
inserting the battery (11).
Inserting the battery
1. Put the rotational direction switch (7) in the middle po-
sition (lock).
2. Push the battery (11) into the battery mount (10). The
battery (11) clicks into place audibly.
Removing the battery
1. Press the unlock button (12) of the battery (11) and
remove it from the battery mount (10).
8.2
Inserting the tool attachment (15/
16/ 17/ 18/ 19) (Fig. 1, 3)
CAUTION
Keep your hands away from the tool attachment when
the product is in operation.
Note:
Clean the shaft of the tool attachment and grease it lightly.
Note:
The dust cap (2) largely prevents drilling dust from enter-
ing the tool receiver during operation. When inserting the
tool attachment*, take care not to damage the dust cap
(2).
ATTENTION
A damaged dust cap must be replaced immediately. It
is recommended to have this done by a service centre.
1. Pull the locking sleeve (3) backwards to unlock the
SDS-Plus tool receiver (1).
2. Insert the tool attachment (15/ 16/ 17/ 18/ 19) into the
SDS-Plus tool receiver (1) by turning it.
3. Release the locking sleeve (3).
4. Check that the tool attachment (15/ 16/ 17/ 18/ 19) is
firmly seated by pulling on it.
The tool attachment (15/ 16/ 17/ 18/ 19) has some ra-
dial play due to the system.
GB | 23

Werbung

loading

Diese Anleitung auch für:

5909241900