YATO YT-73080 Bedienungsanleitung Seite 16

Parameter
Heating time
Working temperature of the soldering tip
Maximum temperature of the soldering tip
Dimensions of the soldering tip
Durability of the soldering tip
Mass
Electric insulation class
Protection rating
GENERAL SAFETY CONDITIONS
NOTE! Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fi re or
injuries. The notion of electric tool used in the instructions applies to all the tools which are powered with electric current,
both wire tools and wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of ac-
cidents. Do not work with electric tools in explosive environments, or those which contain infl ammable liquids,
gases or vapours. Electric tools generate sparks, which may cause a fi re in case of contact with infl ammable gases
or vapours. Do not allow children and outsiders to the place of work. A lack of concentration may result in a loss of
control over the tool.
Electric safety
The plug of the power supply cable must fi t the mains socket. Do not modify the plug. Do not use any adapters
whatsoever in order to adapt the plug to the socket. Unmodifi ed plug which fi ts the socket reduces the risk of an elec-
tric shock. Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body
increases the risk of an electric shock. Do not expose electric tools to precipitation or humidity. Water and humidity
which gets into the electric tool increases the risk of an electric shock. Do not overload the power supply cable. Do
not use the power supply cable in order to carry the tool or to connect and disconnect the plug from the mains
socket. Avoid contact of the power supply cable with heat, oils, sharp tools and moving elements. Damage to
the power supply cable increases the risk of an electric shock. In case work is realised outside closed areas, it is
necessary to use extension cords designed for applications outside closed areas. Using a correct extension cord
permits to reduce the risk of an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if
you are tired or under eff ects of medicines or alcohol. Even a moment's inattention during work may lead to serious
injuries. Always use individual means of protection. Always wear goggles. Using individual means of protection,
such as dust-masks, protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool
to the mains. Holding the tool with a fi nger on the switch or connecting an electric tool when the switch is in the ON posi-
tion may lead to serious injuries. Before you turn an electric tool on remove all the spanners and other tools, which
have been used for adjustments. A spanner left on rotating elements of the tool may lead to serious injuries. Keep
your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situa-
tions during its operation. Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes
and gloves away from moving elements of the electric tool. Loose clothes, jewellery or long hair may get caught on
moving elements of the tool. Use dust extractors or dust containers, if the tool is equipped with any. Make sure
they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the
given work will result in a more effi cient and safer work. Do not use the electric tool if the switch is not functioning
properly. A tool which may not be controlled by means of a switch is dangerous and must be repaired. Disconnect
the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool. It will
permit to avoid accidental activation of the electric tool. Store the tool away from children. Do not allow untrained
16
O P E R A T I N G
GB
Unit of measurement
[min]
[ C]
O
[ C]
O
[mm]
[h]
[kg]
M A N U A L
Value
3
350
400
Ø3,8 x 70
> 60
0,07
I
IP20