EINHELL RT-CS 190 L Originalbetriebsanleitung Seite 16

Anleitung_RT_CS_190_L_SPK1:_
GB
6.2 Using the circular saw
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4)
Ensure that the ON/OFF switch (2) is not
depressed. Only then should you connect the
mains plug to a suitable socket.
Do not switch on the circular saw until you have
fitted a saw blade.
Place the saw foot flat on the workpiece you wish
to saw. The saw blade must not be in contact with
the workpiece.
Hold the circular saw firmly with both hands.
Before you start your sawing work on the
workpiece, you can use the lever (15) to open the
swing guard hood (19) slightly. Starting the
sawing work is then easier.
6.3 Switching ON/OFF (Fig. 9)
To switch on:
Press the locking button (3) and the ON/OFF switch
(2) at the same time
Allow the saw blade to accelerate until it reaches
full speed. Then slowly move the saw blade along
the cutting line. Only exert gentle pressure on the
saw blade as you do so.
To switch off:
Release the locking button and ON/OFF switch
If you release the handle the equipment will shut
down automatically which means that it cannot
operate accidentally.
Ensure that you do not cover or block the
ventilation openings whilst working with the tool.
Do not slow down the saw blade after you switch
it off by pressing it sideways.
Important! Do not put down the machine until the
saw blade has reached a complete standstill.
Important. Carry out a trial cut in a piece of
waste wood
6.4 Changing the saw blade (Fig. 10-13)
Important. Always pull out the power plug
before doing any work on the circular saw!
Only use saw blades of the same type as the saw
blade supplied with this circular saw. Ask your dealer
for advice.
Use the saw blade key (13) supplied to change the
saw blade. The saw blade key (13) is stored in the
soleplate (6). Pull the saw blade key (13) out of the
16
22.04.2010 10:55 Uhr Seite 16
soleplate (6) when you need it.
Important. The hand-held circular saw must not be
operated with the saw blade key (13) inserted in it.
Press the spindle lock (11).
Undo the screw to secure the saw blade (17)
using the saw blade key (13).
Push back and secure the moving swing guard
hood (19) using the lever for the swing guard
hood (20).
Remove the flange (18) and the saw blade (12) in
a downwards direction.
Clean the flange and insert the new saw blade.
Pay attention to the running direction (see arrow
on the guard hood and saw blade).
Tighten the screw to secure the saw blade (17),
check it runs true.
Before you press the On/Off switch, make sure
that the saw blade is correctly fitted and that
moving parts run smoothly and the clamping
screws are tightened securely.
6.5 Using the laser and the LED light (Fig. 14-15)
The laser (24) enables you to make precision
cuts with your circular saw.
The laser light is generated by a laser diode. The
laser light is enlarged to form a line and is emitted
through the laser emission aperture. You can
then use the line as an optical marker for the
sawing line for precision cuts. Follow the laser
safety instructions.
The LED light (23) can be used in poor lighting
conditions to additionally illuminate the cutting
position.
Use the combination switch for the laser/LED light
(22) to switch the laser and the LED light and off.
After inserting the plug into the socket, you can
select the following combinations with the
ON/OFF switch for the laser/LED light.
Press once:
Press twice:
Press three times: Laser ON - LED light ON
Press four times:
The laser beam and the LED lamp can be
affected by deposits of dust and chips. The
emission aperture of the laser beam and the LED
light must therefore be cleaned after each use.
Always switch off the laser when not in use.
Always switch off the LED lamp when not in use.
The laser and LED light are powered by the
mains voltage. Batteries are therefore not
required.
Laser ON
Laser OFF - LED light ON
Laser OFF - LED light ON