Teac VRDS-10 Bedienungsanleitung Seite 7

Operations
Basic Operation =
In addition to the basic operation
buttons on the front panel, the remote
control has buttons for control of all
the same functions (except for the
POWER ON/OFF button). The following
operation descriptions assume that
the remote control unit is used unless
otherwise specified.
1. Press the power switch.
2. Press the open/close button.
The disc tray will slide out and "OPEn'
will be indicated in the display. Place
the disc gently on the tray with its
label side facing upward. The disc is
set within the disc guides at the center
of the tray.
For 8 cm (3-inch)
CD Singles
For 12 cm (5-inch)
Compact Discs
3. Press the open/close button again.
The disc tray will close and "CLOS* will
be indicated in the display.
The DISC IN indicator lights.
Al
C)
=)
Total number of
Total playback
tunes on the disc time —
Ly / | ' uF
VL! i 1c
The above information is displayed.
Several seconds later, the player enters the
standby mode.
4. Press the play button.
Disc playback starts from the first
track, and the » (play) indicator will
light.
CAUTIONS :
© Do not force the tray by hand during
opening and closing operations.
© Do not leave the disc tray open
when the player is not in use to
prevent dirt and dust from entering
the mechanism.
@ Even if the disc tray is open...
Direct access play:
By pressing the numeric buttons
corresponding to the required tune, the
tray will close and play starts from the
specified tune directly, without your
having to press the play button.
Example 1:
To play the 5th tune:
Press (>.
Example 2:
To play the 21st tune:
Press <> twice, then > .
When the play button is pressed:
The disc tray will close and playback
starts from the first track.
When the pause button is pressed:
The tray will close and the player will
enter the pause mode at the beginning of
the first track and the pause m indicator
will light.
To stop play
To stop playback:
Press the stop button. The player enters
the stop mode.
To unload the disc:
Press the open/close button; playback
stops and the disc tray will slide out, and
all functions are reset to their initial
settings.
To temporarily suspend playback (pause
mode):
Press the pause button. Playback stops at
the current position and the Mf indicator
lights steadily. To resume playback from
the same position, press the play button
or pause button again.
@ Single Playback
1. Press the single button. The SINGLE
indicator will light in the display.
2. Press the numeric buttons
corresponding to the required tune.
3. A single tune will be played back, after
which the player will enter the stop
mode.
© To release the single mode, press the
single button again.
i — -_
The program playback function allows you
to program up to 20 tunes (tracks) for
playback in any desired order.
@ Programming required tunes
Example:
To program tunes in the order 2 > 15
— 10 = Bin the stop mode.
| . Press the stop button.
2. Press the program button.
The PROGRAM indicator lights in the
display.
3. Press the numeric buttons in the
following order:
dP nai o g e e aeons 5S :
ee gg | gle | Ma ha OS
Tune No.
on disc
Total program Program No.
| playback time
e If the © button is pressed by
mistake, press the clear button on the
remote control unit to cancel it.
Press the play button.
Programmed playback starts from the
first programmed tune, the 2nd tune on
the disc. When this tune is finished,
the player skips to the 15th tune which
has been stored as the second tune in
the program, etc.
>
The programmed contents will be held
in memory even after programmed
playback has been completed or when
programmed playback is stopped by
pressing the stop (m) button.
When the stop button is pressed in the
stop mode, the contents of the
program are erased.
© To release the program mode, press
the program button again.
During program playback, the TOTAL
REMAIN time display shows the total
remaining time of the programmed
tunes, from the current position.
If tunes with numbers higher than 20
are programmed, either the REMAIN
time or TOTAL REMAIN time may not
appear in the display.
In the playback mode, press the
program button. The current tune will
be programmed as first tune.