Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Before Use
Read This Before Operating
Choose the installation location of your
unit carefully. Avoid placing it in direct
sunlight or close to a source of heat.
Also
avoid
locations
subject to
vibrations and excessive dust, heat,
cold or moisture. Keep away from such
sources
that hum, such as trans-
formers or motors.
Do not open the cabinet as this might
result in damage to the circuitry or
electrical shock. If a foreign object
should get into the set, contact your
dealer.
Be sure not to handle discs with dirty
fingers. Never insert a disc which has
a crack on the surface.
When removing the power plug from
the wall outlet, always pull directly on
the plug, never yank the cord.
To keep the laser-pickup clean, do not
touch it, and do not forget to close the
disc tray.
Do not attempt to clean the unit with
chemical
solvents
as this might
damage the finish. Use a clean, dry
cloth.
Keep this manual in a safe place for
future reference.
Beware of condensation
When the player (or a compact disc) is
moved from a cold to a warm place or
used
after a sudden temperature
change,
there
is the
danger
of
condensation. Water vapor in the air
could condense on the mechanism or
the laser pickup. If droplets of water
form on these parts, correct playback
will be impossible because the laser
cannot read the information from the
disc correctly. To prevent this, if you
are
going to use the
player
in a
condition where condensation could
occur, you should leave the player for
1 or 2 hours after plugging it into an AC
outlet depending
on the amount of
condensation.
If this is done, the
player will stabilize at the temperature
of its surroundings.
Handling
the Discs
This unit has been designed specifically
for reproduction of compact discs bearing
the * JEG" mark. No other discs can be
reproduced.
Always place the compact disc in the
disc tray with the label facing upward.
(Compact discs can be played only on
one side.)
To remove a disc from its storage
case, press down on the center of the
case and lift the disc out, holding it
carefully by the edges.
How to remove the disc
Fingermarks
and dust should
be
carefully
wiped
off the
disc's
recorded surface with a soft cloth.
Wipe radially
Never use such chemicals as record
sprays, antistatic sprays
or fluid,
benzine or thinner to clean compact
discs.
Such
chemicals
will
do
irreparable
damage
to the disc's
plastic surface.
Discs should be returned to their
cases after use to avoid serious
scratches that could cause the laser
pickup to "skip."
Do not expose discs to direct sunlight
or high humidity and temperature for
extended periods.
Long exposure to high temperatures
can warp the disc.
Do not stick paper or write anything
with a ballpoint pen on the surface of
the label side.
Voltage Conversion
(For general
export models)
Be sure to remove the power cord from
the AC outlet before repositioning the
voltage converter switch.
1. Locate the voltage selector on the rear
panel.
2. Using a flat-bladed screwdriver, set to
the appropriate 230 V or 120 V position
according to your area.
VOLTAGE
SELECTOR
ov
230v
IMPORTANT (for U.K. Customers)
The wires in this mains lead are
coloured in accordance
with the
following code:
BLUE:
NEUTRAL
BROWN:
LIVE
As the colours of the wires in the
mains lead of this apparatus may not
correspond
with
the
coloured
markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured BLUE must
be connected to the terminal which is
marked with the letter N or coloured
BLACK. The wire which is coloured
BROWN must be connected to the
terminal which is marked with the
letter L or coloured RED.
In the U.K,, this unit is sold without an
AC plug.
THE APPLIANCE CONFORMS WITH
EEC
DIRECTIVE
87/308/EEC
RE-
GARDING INTERFERENCE SUPPRES-
SION
Werbung
