Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• If you select temperature control, select "Temp" using the
GB
"Temp/heating" key. Now you can programme the required
temperature by means of the arrow keys between 35°C and
240°C in 5°C intervals.
• After programming the capacity or temperature, you can opt
to programme the timer. This timer switches the appliance
off after the programmed time has been reached. You do this
by pressing the "Timer" key after programming the capac-
ity or temperature, and selecting "Timer". You can now set
the desired time. The maximum programmable time is 180
minutes.
• Once you have reached the required result, you can switch
off the appliance by pressing the "ON/OFF" key. The display
will go off and the lights next to "Power", "Temp" and "Timer"
will go off.
• If you do not use the appliance for an extended period, remove
the plug from the wall-mounted electrical socket and remove
the pans from the appliance.
Note:
1. After an extended period of operation, it is normal for the
cooling fan inside to continue running in OFF mode for some
time. Before unplug the appliance, wait until the cooling fan
stops running.
2. The appliance's surface is still hot even after switch to OFF
mode. Please wait the appliance completely cool down before
touching or cleaning.
3. If no cookware is placed on the heating surface after switch
ON, it will turn to OFF mode automatically within 1 min.
4. If no any button on the control panel is pressed during oper-
ation for 2 hours, the appliance will then switch to OFF mode
automatically.
5. If the appliance beeps after being switched on, the pan you
are using is not suitable for induction or the appliance is de-
fective. In case of any doubt, always contact the supplier of
your pan!
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
8
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems
Possible cause
The appliance
- Power plug is not
does not switch
connected properly
ON.
with the electrical
outlet.
- Without switch ON
the appliance by
turn ON the knob.
Cooling fan is op-
- This is normal.
erating even after
The cooling fan
the appliance is
continues running
switched to OFF
in Standby mode
mode.
for some time to
cool down all inter-
nal elements.
Error code identification
Error codes
Possible cause
E01
The temperature
of the appliance is
too high
Cooling fan
defective
E02
The temperature of
the cookware is too
high. Possibly, the
cookware becomes
empty and appli-
ance will shut down
for protection.
Possible solution
- Check the power
plug to make sure
it is connected
properly.
- Switch ON the ap-
pliance by turning
ON the knob.
- Wait until the
cooling fan stops
rotating.
Possible solution
Unplug the appliance,
remove the cookware,
wait until the appliance is
completely cool down.
Contact the supplier.
Unplug the appliance,
remove the cookware,
wait until the appliance is
completely cool down.
Werbung
