Werbung
ModBUS Register Information
Group Name
Setup/Analog Output 2
Setup/Analog Output 2
Setup/Analog Output 2
Setup/Analog Output 2
Setup/Analog Output
2/Linear
Setup/Analog Output
2/Linear
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Analog Output
2/PID
Setup/Relay 1
Setup/Relay 1
Setup/Relay 1
Setup/Relay 1
Setup/Relay 1
Setup/Relay 1/Alarm
Setup/Relay 1/Alarm
Setup/Relay 1/Alarm
Setup/Relay 1/Alarm
Setup/Relay 1/Alarm
Setup/Relay 1/Alarm
Setup/Relay 1/Control
66
Tabelle 16 Controller ModBUS Registers (Fortsetzung)
Tag Name
Register # Data Type
Type
40031
Transfer
40032
Value
Filter
40034
0mA–4mA
40035
Select
Min Setting
40036
Max Setting
40038
Mode
40040
Manual Set
40041
Setpoint
40043
Phase
40045
Proportional
40046
Band
Integral Time
40048
Derivative
40049
Time
Source
40050
Sensor Select
40051
Measurement
40052
Select
Type
40053
Transfer
40054
Setting
High Alarm
40055
Low Alarm
40057
High
40059
Deadband
Low
40061
Deadband
On Delay
40063
Off Delay
40064
Setpoint
40065
Length
R/W
Unsigned
1
R/W
Integer
Float
2
R/W
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Float
2
R/W
Float
2
R/W
Unsigned
1
R/W
Integer
Float
2
R/W
Float
2
R/W
Unsigned
1
R/W
Integer
Float
2
R/W
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Float
2
R/W
Float
2
R/W
Float
2
R/W
Float
2
R/W
Unsigned
1
R/W
Integer
Unsigned
1
R/W
Integer
Float
2
R/W
Description
Selects output type (0 = Linear output;
1 = PID control)
Sets the transfer value
Sets the output filter value in seconds
(0 to 120 seconds)
Selects 0mA/4mA for min output
(0 = 0mA; 1 = 4mA)
Sets the min output value
Sets the max output value
Sets the PID mode (0 = auto; 1 = manual)
Sets the PID manual output value
(0.0 to 100.0%)
Sets the PID setpoint
Sets the PID phase
(0 = Direct; 1 = Reverse)
Sets the PID proportional band
Sets the PID integral time (minutes)
Sets the PID derivative time (minutes)
Selects data source for this relay
(0 = None; 1 = Real Time Clock;
2 = Sensor; 4 = Calculation)
Selects sensor source when
Source = Sensor
(0 = Sensor1; 1 = Sensor2)
Selects measurement on the sensor
(0 = Meas1 .. 3 = Meas4)
Selects the relay type
(0 = Alarm; 1 = Control;
2 = Status; 3 = Timer; 4 = Event)
Selects the transfer value for the relays
(0 = De-energized; 1 = Energized)
Sets the high alarm setpoint
Sets the low alarm setpoint
Sets the high alarm deadband
Sets the low alarm deadband
Sets the on delay time
Sets the off delay time
Sets the controller setpoint
Werbung
