Care And Maintenance; Troubleshooting Guide; Error Correction - Kärcher GSH 2 Plus Bedienungsanleitung

Care and maintenance

DANGER
Risk of injury due to cuts from sharp blades and ac-
cidentally switching on the device!
Remove the security key from the device before all work
on the device!
Make sure that the ON/OFF button is not pressed.
Avoid unintentionally switching on the device.
Wear safety goggles and protective gloves when work-
ing on the device.
Always mount the blade guard before working on the
device and before transporting it.
Cleaning the device
ATTENTION
Risk of damage due to incorrect cleaning!
Only clean the device with a hand-held brush and damp
cloth.
Do not use solvent-based cleaning agents.
Do not immerse the device in water or other liquids.
Do not clean the device with a hose or high-pressure
water jet.
1. Release the ON/OFF button.
The device switches off.
2. Remove the security key from the device.
3. Remove cuttings with a hand-held brush.
Illustration T
4. Remove resin from the blades, e.g. with the Kärcher
Universal Stain Remover RM 769.
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device is not work-
ing.
The device stops during
operation
Charge indicator Error description
An LED flashes slowly The battery is fully discharged.
and the motor is off.
All LEDs flash twice The blades are blocked or contami-
every 2 seconds and nated.
the motor is off.
The temperature protection function
of the motor is activated.
22

Troubleshooting guide

Cause
The security key is not sitting properly in
the device.
The charging state of the battery is too
low.
The battery has overheated.
The battery or charger is defective.
The device is overheated
Error codes and error descriptions
5. Oil the blades of the grass or shrub shears, see
chapter Oiling the blades.
6. Mount the blade guard, see chapter Mounting the
blade guard.
7. Clean the device with a damp cloth if required.
Note
Clean the optionally available telescoping handle in the
same way.
Note
To maintain blade quality and optimum cutting results,
apply a little spray oil or thin machine oil to the blades of
the grass and shrub shears after each use.
1. Release the ON/OFF button.
The device switches off.
2. Remove the security key from the device.
3. Clean the device, see chapter Cleaning the device.
4. Place the device on a horizontal, level and oil-resist-
ant surface.
Illustration U
5. Apply a thin layer of oil to the blades of the grass and
shrub shears.
6. Switch on the device and let it run briefly.
7. Mount the blade guard, see chapter Mounting the
blade guard.
8. Clean the base and dispose of oil residues in an en-
vironmentally friendly manner and in accordance
with local regulations.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
1. Push the security key into the intake on the
device until it you feel it latch into place.
1. Charge the battery, see Chapter Battery
charging.
1. Allow the battery to cool down.
Note
The battery can get very warm.
2. Do not the place the device in direct sun-
light.
1. Replace the battery or charger, see chap-
ter Intended use.
1. Stop working and allow the device to cool
down.

Error correction

1 Charge the battery, see Chapter Battery charging.
1 Release the ON/OFF button.
2 Check whether there are any hard foreign bodies be-
tween the blades and remove them if necessary.
3 Clean and oil the blades, see chapter Cleaning the
device.
1 Allow the device to cool down.
Only use and store the device within the intended
temperature range.
English
Oiling the blades