Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Inserting the battery pack
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Illustration M
1. Push the battery into the mounting in the device until
it audibly latches into place.
Removing the battery
WARNING
Uncontrolled startup
Risk of injury
Remove the battery pack from the device during work
breaks and before carrying out any service or care work.
Illustration N
1. Press the unlocking button.
2. Remove the battery from the device.
Operation
Switching on the device
You must press the unlocking button to enable the trig-
ger (safety function). Only then can the device be
switched on via the trigger.
1. Press the trigger lockout button.
Illustration O
2. Press the trigger at the same time.
The device starts up.
3. Release the trigger lockout button.
The device continues running.
4. Release the trigger.
The device stops.
Removing weeds
Note
Please note that the device only removes weeds at the
surface. It does not remove the roots.
Note
We recommend using the device only in a horizontal,
slightly angled position. Vertical use can result in faster
wear of the bristle strip.
The gentle nylon brush is capable of removing a wide
range of weed types from and between almost any hard
surface. The cleaning results can however vary de-
pending on external influences (ambient humidity,
ground moisture and ambient temperature).
ATTENTION
Risk of damage
Do not scrub with the device or use the protective cover
for scraping. This may damage the device
1. Always guide the device with slow movements over
the surface to be cleaned, at a slight angle without
applying any pressure. Do nor guide the device flat
over the surface.
Illustration P
2. Work on stubborn weeds multiple times slowly.
3. Hold the device at the side of the second handle
when cleaning joints so that it is slightly titled.
Please note that loose material in the joint may also
be removed.
12
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
Correct storage of the device
Store the device by hanging from the eye in the handle.
You can also alternatively place the device on the edge
of the protective cover.
ATTENTION
Risk of damage to the bristles
Do not store the device standing on the bristles.
Care and service
Changing the bristle strip
Note
The bristle strip must be replaced when the bristles
show signs of wear.
1. Remove the battery pack from the device.
2. Screw open the handle lock of the bristle strip holder
in a clockwise direction and remove it.
Illustration G
3. Pull out worn out bristle strip and the removal aid.
4. Join the new bristle strip into a crown by snapping
the ball into the recess.
Illustration H
5. Place the bristle crown into the holder.
Illustration I
6. Put on the guide aid including the bristle strip locking
cover and screw closed in an anti-clockwise direc-
tion.
Illustration J
Replacing the protective cover
WARNING
Risk of injury from flung particles
Use the weed remover only with an intact protective
hood.
The protective cover must be replaced when it shows
signs of wear such as cracks or fractures.
1. Remove bristle strip.
2. Release the lock on the protective cover with a flat-
blade screwdriver.
Illustration Q
3. Pull the protective cover away to the rear.
4. Attach the new protective cover and snap it into
place; see chapter Assembly.
The battery pack must be removed from the device be-
fore cleaning.
ATTENTION
Improper cleaning
Damage to the device
Do not clean the device with a hose or high-pressure
water jet.
Do not use aggressive detergents.
Do not knock the brush on the ground.
English
Transport
Storage
Cleaning
Werbung
Kapitel
Fehlerbehebung
