Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
S
a
f
e
S
a
f
e
Take note of the following instructions
to protect yourself and others from
hazards and injuries.
• Observe local accident prevention and safety
regulations in the work area.
• The operator is responsible for third parties in
the work area.
• Keep children away from machine.
• Persons younger than 16 years of age are not
allowed to operate the machine.
• Be sure that there is enough light.
• All dangerous parts have been covered with
safeguards for your protection. Do not modify
or remove the safeguards.
• Never modify the machine or parts thereof.
• Only start up the machine if the protective
devices are complete and undamaged.
• Always fix tightly tilting angle control during
storage, transport and operation.
• Faulty or damaged parts in the device must
be replaced immediately.
• Set up and run the machine on a solid, level
base only (where it will not tip over).
• Make sure that there is no danger of tripping
near the machine.
• Only use the machine for the functions listed in
"Proper use".
• Wear protective goggles and eye protection
while working with the machine.
• Do not spray machine with water (this is
hazardous due to live components).
• Do not leave the machine standing in the rain
or use when raining. Store the machine in a
dry place.
• Be absolutely sure to
pull the plug before:
-
adjust the angle
-
moving or transport
-
cleaning, maintenance or repair work
Electrical safety
• Connecting attachments must be designed in
conformance with IEC 245-4:1980
(DIN 57 282) and marked H 07 RN-F, or
comparable models. Cross section of wires at
least 3 x 1.5 mm² up to a maximum length of
50 m. Wire cross-section at least 2.5 mm² for
lengths of more than 50 m.
• Use only connecting attachments with a
rubber plug device that is protected against
spraying water
• Check connecting attachments for defects or
ageing before using them.
w
o
r
k
i
n
g
w
o
r
k
i
n
g
.
• Never use defective connecting attachments.
• When laying the connecting attachments, be
sure that they do get crushed or bent, and that
the plug-and-socket connection does not get
wet.
• Do not use any provisional electrical
connections.
• Never bridge over protective devices or put
them out of operation.
• Connect the machine using a fault current
protection switch.
A licensed professional electrician must
make all electrical connections and repairs,
and observe local regulations in doing so,
especially those regarding protective measures.
The manufacturer or a company designated by
the manufacturer must attend to the repair of all
electrical parts on the machine.
Observe all safety instructions.
• Check that the machine is completely and
correctly assembled.
• Set the machine on a solid, level base.
• Connect the machine to an appropriate and
correctly wired electric socket.
• Only use extension leads with sufficient dia-
meters:
- cable up to 50 metres: diameter at least
- cable over 50 metres: diameter at least
• Fuse protection: 10 A
• Before using the machine, make sure each
time that
- there are no faulty connections
- all screws are tight
- whether tilting angle control is properly
tightened.
Switching on and off
red
0 = OFF
green
= ON
Switch the motor on and off only at the switch.
In the event of a power failure, the machine will
switch off automatically. Press the switch
again to restart the machine.
Motor protection
The motor is equipped with a thermostat. The
thermostat switches the motor off automatically in
the event of overload (overheating). The machine
can be restarted after a cooling-off period.
11
S
t
a
r
t
u
p
S
t
a
r
t
u
p
1,5 mm².
2,5 mm².
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
