Assembly; Before Commissioning - Scheppach MR760-E Original Bedienungsanleitung

7. Carefully remove the battery-powered ride-on
lawnmower from the pallet with 3 other people.
8. Grip the device by the frame - not by the plastic
casing!
9. If possible, keep the packaging until the expiry of
the warranty period.
m DANGER
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!

8. Assembly

m WARNING!
Risk of injury and damage!
The use of incorrect spare parts and accessories can
lead to injuries and damage. These could come loose
and be flung away. They can also reduce the power of
the product.
- Only use original spare parts and accessories from
the manufacturer. Original spare parts or accesso-
ries can be obtained from your dealer.
- Failure to do so may reduce the power of the prod-
uct and parts may come loose.
- Failure to observe this will invalidate the manufac-
turer's warranty.
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the instruc-
tions below.
m ATTENTION!
Remove the ignition key before carrying out any work
on the device!
8.1 Fitting the seat (Fig. 5 & 6)
1. Mount the seat (2) by first tightening the 2 screws
M8x16 (27) and M8 nuts (28) by hand using the
open-end spanner.
2. Now tighten the 2 screws (27) using the open-end
spanner.
3. Now connect the cable of the seat contact switch
(b) (Fig. 6).
8.2 Fitting the steering rod (Fig. 3)
1. Insert the steering rod (37) into the steering socket
(a).
2. Make sure that the drill holes are on top of each
other.
3. Then put the M8x25 screw (29) through the steer-
ing rod and place on the M8 nut (28).
4. Tighten the screw using the open-end spanner.
8.3 Fitting the steering wheel (Fig. 4)
1. Slide the steering rod cover (36) over the previ-
ously mounted steering rod (37).
2. Place a plastic washer (34) on the steering rod.
3. Place the plastic sleeve (32) on the steering rod.
4. Place the second plastic washer (34) on the steer-
ing rod.
5. Next, place the steering wheel mounting (31) on
the steering rod.
6. Place the steering wheel (1) on the steering wheel
mounting (31).
7. Now insert the spring washer (33) into the steering
wheel (1) and attach the steering wheel using the
M8 nut (28).
8. Place the steering wheel cover (35) in the middle
of the steering wheel (1) until it engages.
8.4 Connecting the mower to the rechargeable
batteries (Fig. 7)
1. Remove the cover (c) carefully.
2. Connect the cables (d) underneath to each other in
order to connect the mower to the rechargeable bat-
tery.
3. The mower is now operational.

9. Before commissioning

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Before each commissioning, check the product for
the following:
• Faultless condition and completeness of the guards
and the cutting device
• Tight fit of all screw connections
• Smooth running of all moving parts.
Check before each commissioning,
• whether the cutting tool and the entire cutting unit
(mowing blade, blade coupling, blade brake, mount-
ing bolts, mowing unit housing) are in perfect con-
dition. Particular attention must be paid to secure
seating, damage and wear.
• whether the safety devices are in perfect condition
and function properly.
• whether tyres (air pressure, damage, wear) and
frame are in perfect condition. Screw connections
must be checked for tightness. In particular, all
maintenance work listed in the maintenance sched-
ule under the heading "Before each commissioning"
must be carried out.
Replace defective parts and all other worn and dam-
aged parts before using the device. Illegible or dam-
aged danger and warning information on the device
must be renewed.
If necessary, consult a specialist dealer.
www.scheppach.com
GB | 41