Scheppach DECO-XLS Original Bedienungsanleitung Seite 31

4. Then loosen the upper saw blade clamping lever
(28), followed by the lower saw blade clamping le-
ver (29) using the Allen key (23).
8.1.2 Inserting the saw
(optional)
The teeth of the saw blade must always point down-
wards.
1. First, secure the saw blade (22) in the lower saw
blade mounting (30). To secure the saw blade (22),
tighten the lower saw blade clamping screw (29)
using the Allen key (23).
2. Press the support (12) down lightly. Fasten the oth-
er end of the saw blade (22) in the top saw blade
holder (27) (see fig. 9).
3. Fix the saw blade (22) with the upper blade clamp-
ing screw (28) (see fig. 10).
4. Tighten the saw blade (22) with the clamping lever
(11), by pressing it down again. Check the tension
of the saw blade (22). If the tension is insufficient,
it can be increased by turning the lever clockwise.
First release the clamping lever (11).
5. Put the table insert (26) back.
8.1.3 Removing the saw blade with pins
1. To remove the saw blade (22), lift the table insert
(26) upwards.
2. First, release the tension by flipping the tension
lever (11) upwards. Continue reducing the tension
by turning clockwise as required.
3. Press the support (12) down lightly (see fig. 9).
4. Pull the saw blade from the upper and lower saw
blade mounting (27/30).
8.1.4 Inserting the saw blade with pins
The teeth of the saw blade must always point down-
wards.
1. Insert one end of the saw blade (22) through the
drilled hole in the table. Insert the pins of the saw
blade (22) into the corresponding recesses of the
top and bottom saw blade holder (27/30).
2. First insert the saw blade (22), in the lower blade
holder (30).
3. Press the support (12) down lightly (see fig. 9).
4. Check the position of the saw blade pins in the saw
blade mountings (27/30).
5. Tighten the saw blade (22) with the clamping lever
(11), by pressing it down again. Check the tension
of the saw blade (22). If the tension is insufficient,
it can be increased by turning the lever (11) clock-
wise.
blade without pins
www.scheppach.com
6. Put the table insert (26) back.
NOTE
The left side features a storage box (9), which enables
you to stow replacement saw blades and the hexagon
wrench.
8.2 Checking the saw blade tension
WARNING
Check the blade tension regularly and after insert-
ing a saw blade.
Tension the saw blade after assembly by pressing
down on the tension lever (11).
If the blade tension is too low or too high, proceed as
follows:
• Fold the tension lever (11) upwards.
• Turn the tension lever (11) clockwise to increase the
tension and anti-clockwise to reduce it.
• Press the tension lever down again to engage the
setting.
If the tension is correct, the saw blade should produce
a light tone when it is plucked, like a string.
8.3 Calibrating the angle scale (fig. 12, 12.1)
IMPORTANT
Check the adjustment of the angular scale before you
start working with the unit.
1. Loosen the locknut of the adjustment screw (37).
2. To set the saw table, use a 90° bracket (31, not in
the scope of delivery). Place this against the saw
table and the saw blade (fig. 12).
3. Adjust the adjustment screw (37) until the angle
between the saw blade (22) and the saw table (6)
is 90°.
4. Tighten the locknut of the adjustment screw (37)
again.
5. Loosen the screw (32) and turn the pointer (33) to
the 0° marking.
6. Make a test cut. Check the angle on the workpiece
with a protractor. If necessary, readjust the pointer
(33).
8.4 Installing the blow-off device (fig. 8)
1. Ensure that the saw blade guard (5) folded down.
2. Screw the blow-off device (1) clockwise onto the
holder (2) as described in fig. 8.
GB | 31