Unpacking; Before First Use - Scheppach MS150-42E SE Original Bedienungsanleitung

Noise data
Sound pressure L 82 dB (A)
PA
Uncertainty K
PA
Sound power L
WA
Uncertainty K
WA
Vibration parameter
Vibration a
hv
Uncertainty K
h
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
When using the petrol lawn mower for extended peri-
ods, vibration-induced circulatory problems may occur
(white finger disease).
We cannot give exact details about the duration of use
in this case because it is different for each individual.
The following factors can influence the condition:
• Circulatory problems in the user's hands
• Low outside temperatures
• Extended periods of use
We therefore recommend you wear warm work gloves
and take regular breaks.
7.

Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the packag-
ing and transport bracing (if available)
Check that the delivery is complete.
Check the device and its spare parts for possible dam-
age caused by transportation. In the event of com-
plaints, you must contact the distributor without delay.
Claims at a later stage will not be accepted.
If possible, store the packaging until the warranty pe-
riod has expired
Before handling the device, make yourself familiar with
it by reading the operating instructions.
For accessories, consumables and spare parts, only
use original parts. Spare parts are available from your
stockist. Include our item number, the device model
and year of manufacture in your order.
3 dB(A)
92,8 dB (A)
1,86 dB(A)
8,125 m/s²
1,5 m/s²
www.scheppach.com
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

8. Before first use

m ATTENTION!
Always make sure the device is fully assembled
before start-up!
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the instruc-
tions below.
Important! You will need the following additional tools (not
supplied) for assembly, and also for maintenance work:
• A 1 litre measuring jug (oil/petrol resistant)
• A petrol can (5 litres is sufficient for approx. 6 oper-
ating hours)
• A funnel (suitable for the tanks petrol filler neck)
• Household wipes (to wipe up oil/petrol residue; dis-
pose of these at a filling station)
• A petrol suction pump (plastic, available from DIY
stores)
• An oil can with hand pump (available from DIY stores)
• 0,4 litre of engine oil (SAE 30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present.
2. Attach the lower push bar (4a) to both sides of the
mower with one screw (a), 1 washer (c), 1 plastic star
grip nut (5) each. Make sure that the cables, which
will be attached later, are not in the way (fig. 2-3).
3. Attach the upper push bar (4) on the lower push bar
(4a) with one screw (a), one washer (b), one plastic
star grip nut (5) each on both sides (Fig. 4-5).
4. Guide the gas throttle through the electric starter
unit as shown in figure 5a.
5. Insert the throttle cable into the engine brake lever
(3) using a plier. (fig. 5b-5c)
6. Secure the electric starter unit (18) using the
screws (f) on the upper push bar (4). (fig. 5d)
7. Insert the pull start handle (17) in the designated
hook as shown in Fig. 6.
8. Fix the cables to the push bar with the cable clips
(18) provided (fig. 7).
9. Grass box (16) - open it up and click the plastic
clips into position on the frame (fig. 8).
GB | 37