Scheppach HM140L Original Bedienungsanleitung Seite 32

• 45° - position angle stop (b) between the saw blade
(7) and rotary table (16).
• Slacken the counternut (c). Adjust the adjusting
screw (31) until the angle between the saw blade
(7) and rotary table (16) is precisely 45°.
• Retighten the counternut (d) to secure this setting.
8.4 Cross cut 90° and turntable 0° (Fig. 1, 2, 6, 7)
In the case of cutting widths up to approx. 100 mm it
is possible to fix the traction function of the saw with
the set screw (23) in the rear position. In this position
the machine can be operated in cross cutting mode. If
the cutting width is over 100 mm then it is necessary
to ensure that the set screw (23) is loose and the ma-
chine head (5) can move.
Attention! For 90° mitre cuts, the moveable stop rail
(28) must be fixed in the inner position.
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) inwards.
• The moveable stop rail (28) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 5 mm.
• Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade (7).
• Tighten the set screw (29) again. (2x 8.3 +8.4)
• Move the machine head (5) to its upper position.
• Use the handle (1) to push back the machine head
(5) and fix it in this position if required (dependent
on the cutting width).
• Place the piece of wood to be cut at the stop rail (18)
and on the turntable (16).
• Lock the material with the clamping device (8) on
the fixed saw table (16) to prevent the material from
moving during the cutting operation.
• Release the lock switch (3) and press the ON/
OFFswitch (2) to start the motor.
• With the drag guide (23) fixed in place:
use the handle (1) to move the machine head (5) stead-
ily and with light pressure downwards until the saw
blade (7) has completely cut through the work piece.
• With the drag guide (23) not fixed in place:
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the work piece.
• When the cutting operation is completed, move
the machine head (5) back to its upper (home)
position and release the ON/OFF button (2).
32 | GB
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not
release the handle (1) after completing the cut; in-
stead allow the machine head to move upwards
slowly whilst applying light counter pressure.
8.5 Cross cut 90° and turntable 0° - 45° (Fig. 1, 6, 7)
The crosscut saw can be used to make crosscuts of
0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be fixed in the outer po-
sition.
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) outwards.
• The moveable stop rail (28) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 5 mm.
• Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade
(7).
• Tighten the set screw (29) again. (2x 8.6 + 8.7)
• Use the handle (13) to adjust the rotary table (16)
to the desired angle. The pointer (14) on the rotary
table (16) must match the desired angle on the scale
(15) on the fixed saw table (17).
• Tilt the locking lever (13) back up again to fix the
rotary table (16) in place.
• Cut as described under section 8.3.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1, 2, 6, 8)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the out-
er position.
• Open the locking lever (29) for the adjustable stop
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking lever (29) again.
• Move the machine head (5) to the top position.
• Fix the rotary table (16) in the 0° position.
www.scheppach.com