Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
WARNING:
W ear ear protection.
WARNING:
The noise emission during actual
use of the power tool can di er from the declared
value(s) depending on the w ays in w hich the
tool is used especially w hat kind of w orkpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
o and when it is running idle in addition to the
trigger time).
Vibration
T h e f o l l o w i n g t a b l e s h o w s t h e v i b r a t i o n t o t a l v a l u e
( t r i - a x i a l v e c t o r s u m ) d e t e r m i n e d a c c o r d i n g t o a p p l i c a -
b l e s t a n d a r d .
W ork mode
Vibration
emission
2
H a m m e r
7.5 m / s
d r i l l i n g i n t o
2
7.5 m / s
c o n c r e t e
( a
)
h , H D
2
H a m m e r
7.6 m / s
d r i l l i n g i n t o
2
7.7 m / s
c o n c r e t e w i t h
DX 16 ( a
)
h , H D
* T h e t e s t c o n d i t i o n o f r e c o m m e n d e d p r a c t i c a l o p e r a t i o n
m e e t s E N 6 28 4 1-2- 6 , e x c e p t f o r t h e f o l l o w i n g p o i n t s :
•
F e e d f o r c e i s a p p l i e d t o t h e s w i t c h h a n d l e ( m a i n
handle) for working accuracy and e ciency.
The side grip/handle (auxiliary handle) is held to
k e e p b a l a n c e o f t h e t o o l .
NOTE: T h e d e c l a r e d v i b r a t i o n t o t a l v a l u e ( s ) h a s b e e n
m e a s u r e d i n a c c o r d a n c e w i t h a s t a n d a r d t e s t m e t h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can di er from the
declared value(s) depending on the w ays in w hich
the tool is used especially w hat kind of w orkpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
o and when it is running idle in addition to the
trigger time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
t o t h i s i n s t r u c t i o n m a n u a l .
Uncertainty (K) Applicable
standard /
Test condition
2
1.5 m / s
EN 6 284 1-2-6
2
1.5 m / s
R e c o m m e n d e d
p r a c t i c a l
o p e r a t i o n *
2
1.7 m / s
EN 6 284 1-2-6
2
1.5 m / s
R e c o m m e n d e d
p r a c t i c a l
o p e r a t i o n *
SAFETY W ARNINGS
General pow er tool safety w arnings
WARNING Read all safety w arnings, instruc-
tions, illustrations and speci cations provided with
this po w er tool. F a i l u r e t o f o l l o w a l l i n s t r u c t i o n s l i s t e d
below may result in electric shock, fire and/or serious
injury.
Save all w arnings and instruc-
tions for future reference.
The term power tool in the warnings refers to your
mains-operated (corded) power tool or battery-operated
( c o r d l e s s ) p o w e r t o o l .
CORDLESS ROTARY HAMMER
SAFETY W ARNINGS
Safety instructions for all operations
1.
W ear ear protectors. E x p o s u r e t o n o i s e c a n
c a u s e h e a r i n g l o s s .
2.
Use auxiliary handle(s), if supplied w ith the
tool. Loss of control can cause personal injury.
Hold the po w er tool by insulated gripping sur-
3.
faces, w hen performing an operation w here the
cutting accessory may contact hidden w iring.
Cutting accessory contacting a live wire may
m a k e e x p o s e d m e t a l p a r t s o f t h e p o w e r t o o l " l i v e "
a n d c o u l d g i v e t h e o p e r a t o r a n e l e c t r i c s h o c k .
Safety instructions w hen using long drill bits w ith
rotary hammers
1.
Al w ays start drilling at lo w speed and w ith the
bit tip in contact w ith the w orkpiece. A t h i g h e r
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting
in personal injury.
Apply pressure only in direct line w ith the bit
2.
and do not apply excessive pressure. B i t s c a n
b e n d , c a u s i n g b r e a k a g e o r l o s s o f c o n t r o l , r e s u l t -
ing in personal injury.
Additional safety w arnings
1.
W ear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you w ear a dust mask and thickly
padded gloves.
2.
Be sure the bit is secured in place before
operation.
3.
Under normal operation, the tool is designed
to produce vibration. The scre w s can come
loose easily, causing a breakdo w n or accident.
Check tightness of scre w s carefully before
operation.
4 .
In cold w eather or w hen the tool has not been
used for a long time, let the tool w arm up for
a w hile by operating it under no load. This
w ill loosen up the lubrication. W ithout proper
warm-up, hammering operation is di cult.
Always be sure you have a rm footing. Be
5.
sure no one is belo w w hen using the tool in
high locations.
9 ENGLISH
Werbung
Inhaltsverzeichnis
