Makita DHR183 Betriebsanleitung Seite 12

Protections against other causes
Protection system is also designed for other causes that could
damage the tool and allows the tool to stop automatically.
T a k e a l l t h e f o l l o w i n g s t e p s t o c l e a r t h e c a u s e s , w h e n t h e t o o l
has been brought to a temporary halt or stop in operation.
1. Turn the tool o , and then turn it on again to restart.
. Charge the battery(ies) or replace it/them with
recharged battery(ies).
. Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
Sw itch action
WARNING:
Before installing the battery car-
tridge into the tool, al w ays check to see that the
s w itch trigger actuates properly and returns to
the " OFF " position w hen released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
t r i g g e r . R e l e a s e t h e s w i t c h t r i g g e r t o s t o p .
Fig.3: 1. S w i t c h t r i g g e r
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
P u l l t h e s w i t c h t r i g g e r t o l i g h t u p t h e l a m p . T h e l a m p
k e e p s o n l i g h t i n g w h i l e t h e s w i t c h t r i g g e r i s b e i n g p u l l e d .
The lamp goes out approximately 1 seconds after
r e l e a s i n g t h e s w i t c h t r i g g e r .
Fig.4: 1. L a m p
NOTE: Use a dry cloth to wipe the dirt o the lens of
t h e l a m p . B e c a r e f u l n o t t o s c r a t c h t h e l e n s o f l a m p , o r
it may lower the illumination.
NOTE: When the tool is overheated, the lamp flashes.
I n t h i s c a s e , r e l e a s e t h e s w i t c h t r i g g e r a n d t h e n c o o l
down the tool/battery before operating again.
NOTE: T h e f r o n t l a m p c a n n o t b e u s e d w h i l e t h e d u s t c o l -
lection system (optional accessory) is installed in the tool.
Reversing sw itch action
CAUTION:
Al w ays check the direction of
rotation before operation.
CAUTION:
Use the reversing s w itch only after
the tool comes to a complete stop. C h a n g i n g t h e
direction of rotation before the tool stops may dam-
a g e t h e t o o l .
CAUTION:
W hen not operating the tool,
al w ays set the reversing s w itch lever to the neu-
tral position.
T h i s t o o l h a s a r e v e r s i n g s w i t c h t o c h a n g e t h e d i r e c t i o n
o f r o t a t i o n . D e p r e s s t h e r e v e r s i n g s w i t c h l e v e r f r o m
A s i d e f o r c l o c k w i s e r o t a t i o n o r f r o m
t e r c l o c k w i s e r o t a t i o n .
W h e n t h e r e v e r s i n g s w i t c h l e v e r i s i n t h e n e u t r a l p o s i -
t i o n , t h e s w i t c h t r i g g e r c a n n o t b e p u l l e d .
Fig.5: 1. R e v e r s i n g s w i t c h l e v e r
t h e
t h e B s i d e f o r c o u n -
12 ENGLISH
Selecting the action mode
NOTICE:
Do not rotate the action mode chang-
ing knob w hen the tool is running. T h e t o o l w i l l b e
d a m a g e d .
NOTICE:
To avoid rapid w ear on the mode
change mechanism, be sure that the action mode
changing knob is al w ays positively located in one
of the action mode positions.
Rotation w ith hammering
For drilling in concrete, masonry, etc., rotate the action mode
c h a n g i n g k n o b t o t h e symbol. Use a carbide-tipped drill bit.
Fig.6: 1. A c t i o n m o d e c h a n g i n g k n o b
Rotation only
F o r d r i l l i n g i n w o o d , m e t a l o r p l a s t i c m a t e r i a l s , r o t a t e t h e a c t i o n m o d e
c h a n g i n g k n o b t o t h e symbol. Use a twist drill bit or wood drill bit.
Fig.7: 1. A c t i o n m o d e c h a n g i n g k n o b
Electronic function
T h e t o o l i s e q u i p p e d w i t h t h e e l e c t r o n i c f u n c t i o n s f o r
easy operation.
• E l e c t r i c b r a k e
T h i s t o o l i s e q u i p p e d w i t h a n e l e c t r i c b r a k e . I f t h e
tool consistently fails to quickly cease to function
a f t e r t h e s w i t c h t r i g g e r i s r e l e a s e d , h a v e t h e t o o l
s e r v i c e d a t a M a k i t a s e r v i c e c e n t e r .
• C o n s t a n t s p e e d c o n t r o l
T h e s p e e d c o n t r o l f u n c t i o n p r o v i d e s t h e c o n s t a n t
r o t a t i o n s p e e d r e g a r d l e s s o f l o a d c o n d i t i o n s .
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any w ork on the tool.
Side grip (auxiliary handle)
CAUTION:
Al w ays use the side grip to ensure
safe operation.
CAUTION:
After installing or adjusting the
side grip, make sure that the side grip is rmly
secured w ith the protrusions on the tool are fully
engaged by the grooves on the side grip.
T o i n s t a l l t h e s i d e g r i p , f o l l o w t h e s t e p s b e l o w .
1.
L o o s e n t h e t h u m b s c r e w o n t h e s i d e g r i p .
Fig.8: 1. T h u m b s c r e w
2. I n s t a l l t h e s i d e g r i p s o t h a t t h e g r o o v e s o n t h e
grip fit in the protrusions on the tool while pressing the
t h u m b s c r e w .
Fig.9: 1. T h u m b s c r e w
3.
T i g h t e n t h e t h u m b s c r e w t o s e c u r e t h e g r i p . T h e
grip can be fixed at desired angle.