Functional Description - Makita DHR183 Betriebsanleitung

Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Al w ays stop tool operation and
charge the battery cartridge w hen you notice
less tool po w er.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge w ith room tem-
perature at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let
a hot battery cartridge cool do w n before
charging it.
4 . W hen not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION:
Al w ays be sure that the tool is
switched o and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch o the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip o your hands
and result in damage to the tool and battery cartridge
and a personal injury.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
To remove the battery cartridge, slide it from the tool
w h i l e s l i d i n g t h e b u t t o n o n t h e f r o n t o f t h e c a r t r i d g e .
Fig.1: 1. R e d i n d i c a t o r 2. B u t t o n 3. Battery cartridge
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. I f n o t ,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
l i g h t u p f o r a f e w s e c o n d s .
Fig.2: 1. I n d i c a t o r l a m p s 2. C h e c k b u t t o n
Indicator lamps
Lighted
NOTE: D e p e n d i n g o n t h e c o n d i t i o n s o f u s e a n d t h e
ambient temperature, the indication may di er slightly
from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts o power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
p l a c e d u n d e r o n e o f t h e f o l l o w i n g c o n d i t i o n s :
Overload protection
When the battery is operated in a manner that causes
it to draw an abnormally high current, the tool automat-
ically stops without any indication. In this situation, turn
the tool o and stop the application that caused the tool
t o b e c o m e o v e r l o a d e d . T h e n t u r n t h e t o o l o n t o r e s t a r t .
Overheat protection
When the tool or battery is overheated, the tool stops
automatically. In this case, let the tool and battery cool
b e f o r e t u r n i n g t h e t o o l o n a g a i n .
NOTE: W h e n t h e t o o l i s o v e r h e a t e d , t h e l a m p b l i n k s .
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
11 ENGLISH
O Blinking
m a l f u n c t i o n e d .
Remaining
capacity
75% t o 100%
50% t o 75%
25% t o 50%
0% t o 25%
C h a r g e t h e
battery.
The battery
may have