General Instructions - Tractel Corso Cleantech Installations-, Gebrauchs- Und Wartungsanleitung

accidents. It does not cover normal wear and tear,
ageing, the effects of oxidation or variations of voltage
applied to electrical components. It does not apply to
the paint or surface coatings.
The guarantee only applies to original TRACTEL
parts, including the chains, and excludes all other
components.
Repairs under guarantee are automatically performed
in the workshops of the manufacturer or his approved
represen tative. This guarantee commitment only applies
to the cost of the parts replaced and the labour used.
Any travelling or accom mo dation expenses incurred by
TRACTEL personnel or those of TRACTEL's approved
®
representative at the user's site, and the costs of
transporting the item to and from the manufacturer's
factory or that of his approved representative, remain
the res pon sibility of the holder of the guarantee.
Parts which have been replaced become the property
of the manufacturer and must be returned to him.
Any repair or modification work performed by the
purchaser, the user or a third party not approved by
TRACTEL , automatically invalidates the guarantee.
®
Repairs and replacements carried out in accordance
with the guarantee will not extend the initial guarantee
period. This guarantee excludes any work other than
that defined above.
The performance of this guarantee excludes any
acknowledgement of liability for damage or loss of any
type.
The validity of our guarantee remains subject to the
presentation of the guarantee certificate, duly signed
and dated by the manufacturer, with the device
in question. If necessary or in the absence of the
guarantee certificate, it is subject to the purchase
invoice being submitted to the TRACTEL

3. General instructions

1) Receipt of the equipment
Corso™ Cleantech push trolleys are supplied in
cardboard packaging with internal packing. When the
equipment is received, carry out a visual inspection to
check that the packaging is in good condition.
If there is any problem, express the usual reservations
to the carrier.
After unpacking, check that the trolley corresponds to
your order and that the delivery includes:
• Two identical side plates, each fitted with two running
wheels.
• A double threaded mounting bar.
• Two pins and two locknuts on the mounting bar.
• Spacers to adjust distance between side plates.
• These operating and maintenance instructions.
®
• The CE and UKCA declaration of conformity.
2) Installation
The lifetime of a trolley depends on how it is installed.
It is essential to read these instructions carefully so
that you install, use and maintain your device in a
clean condition. Any use contrary to our instructions
is dangerous and will release us from our liability as
manufacturer.
Do not use the device without having read these
instructions in full and understood them.
These instructions must be kept close to the device
at all times, available to the operator and the person
responsible for maintenance.
Follow the safety rules and ensure that they are
followed by others.
2.1 Assembling and anchoring the device
1. Dismantle the trolley by removing the safety pins
and the fixing nuts at each end of the fixing bar.
2. Separate the two side plates taking care to ensure
that the spacer washers and the anchor point are
kept together.
3. Position a side plate on each side of the beam and
pass the fixing bar through the housing of each side
plate with the anchor point in the middle.
4. Begining with the thickest, the spacer washers
should be fitted onto the fixing bar. Remove the side
plates in turn and replace them with appropriate
spacer washers to achieve the best adjustment on
network.
®
the beam, so that the load bearing point is in the
centre of the contact area. The person assembling
the trolley should take great care to ensure that the
sides of the wheels do not touch the central section
of the beam.
5. Distribute the remaining spacer washers equally on
the fixing bar on the outside of each side plate and
then fit the fixing nuts.
6. Tighten the fixing nuts and place the safety pin in
their sockets, then fold the ends of the pins against
the flanks of each nut.
7. Push the trolley along the beam without any load.
Traversing should be smooth.
After positioning the Corso™ Cleantech trolley on
the beam, it is essential to check, WITH NO LOAD
on the trolley, that it moves smoothly and freely
along the whole length of the beam.
EN
5