Additional Safety Warnings - HIKOKI CB 3612DA Bedienungsanleitung

c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
CORDLESS BAND SAW SAFETY
WARNINGS
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Always hold the tool fi rmly with both hands on handle
and front handle (Fig. 2). Do not touch the metal part.
2. Make sure that the area to be cut is absolutely free of any
hidden obstructions including electrical wiring, water, or
gas pipes. Cutting into the aforementioned may result in
electric shock or short circuit, gas leak or other hazards
that can cause serious accidents or injuries.
3. Make sure to securely hold the tool during operation.
Failure to do so can result in accidents or injuries.
4. Setting up and checking the work environment. Check
if the work environment is suitable by following the
precaution.
5. Dust particles such as silica or asbestos are hazardous
to your health. When working with materials containing
these components, take appropriate dust-proofi ng
measures.
6. Working with metal can cause sparks. Make sure there
are no fl ammable and combustible materials in the
vicinity and that they are stored in a safe location.
7. Prior to operation, be sure the blade pulley cover is
closed and fastened with screws.
Operating the tool with the blade pulley cover open may
result in injury.
8. During operation, do not put your hands, face, or other
body parts near the rotating band saw blade or other
rotating parts. Doing so may result in injury.
9. If the main unit is accidentally dropped or suff ers any
impact, carefully inspect the band saw blade, the
unit, etc. to be sure there are no damages, cracks, or
deformations.
Injury may result if there are any damages, cracks, or
deformations.
10. During operation, if the unit is not running smoothly,
or there are abnormal sounds or vibrations, promptly
switch off the unit, discontinue use and contact a HiKOKI
Authorized Service Center for inspection and/or repairs.
Continuing use under these conditions may result in
injury.
11. When using this unit continuously, the unit may overheat,
leading to damage in the motor and switch. Please leave
it without using it for approximately 15 minutes.
12. Follow the instruction manual and make sure that the
band saw blade and accessories are properly installed.
Improper installation may result in injury from parts
coming loose.
13. Securely fasten the workpiece to be cut.
If the workpiece is not securely fastened, it may shift
position and cause damage to the band saw blade and/
or injury.
14. To avoid having the band saw blade clamped between
the cut surfaces during or immediately after cutting, set
up a support stand to bear the weight of the workpiece,
placing it near the section to be cut.
If the band saw blade becomes clamped, it may result in
injury.
15. If the section to be cut off is large, set up another stable
support stand to bear the weight of that section as well.
Not using such a support may result in injury.
16. During operation, do not wear cloth work gloves or other
similar hand protection that may get caught in the unit.
Getting caught in the rotating section of the tool may
result in injury.
17. Prior to operation, verify the safety of the surrounding
area and run the blade briefl y to make sure that there
are no abnormalities in the vibrations of the unit or in the
band saw blade.
If there are such abnormalities, unexpected movements
may occur and cause injury.
18. When working in a high location, ensure that there are no
people below.
Dropping the workpiece or the cordless tool from a high
location may result in an accident.
19. Do not apply any sudden impact to the workpiece with
the band saw blade.
Doing so may damage the band saw blade and/or result
in injury.
20. Use the product's own weight or press gently to cut a
workpiece.
Applying unnecessary force while cutting can result in
detachment of or damage to the band saw blade which
may cause injury.
21. Do not touch the band saw blade, the workpiece, or
shavings with bare hands immediately after cutting, as
they will be hot.
Doing so may result in burns.
22. Remove any shavings adhering to the band saw blade
or blade pulley rubbers as well as any shavings that
accumulates inside the pulley guard (A), (B).
The shavings may cause the band saw blade to detach
or slip, and result in injury.
23. Install the battery properly.
If the battery is not installed properly, it may fall off and
cause injury.
24. When adjusting the amount of protrusion of the guide
plate, be sure to switch off the power and detach the
battery from the cordless tool to avoid any accidents.
25. Do not stare into the LED light or expose your eyes
directly to the light from the LED light.
Continuously exposing your eyes to the light from the
LED light may result in eye injury.
26. Make sure the blade pulley cover is properly attached
before use.
If the band saw blade is damaged or comes loose, it may
result in injury.
9
English