Maschio Gaspardo BISONTE 220 Gebrauch Und Wartung Seite 44

ENGLISH
• With PTO off.
• With tractor motor off.
• With the tractor's ignition key removed.
• With all rotating parts stationary.
Transport on Road
1) When driving on public roads, be sure to follow the highway
code of the country involved.
2) Any transport accessories must be provided with suitable signs
and guards.
3) It is very important to remember that road holding capacity
as well as direction and braking capacity can be infl uenced,
sometimes con-siderably, by equipment being either carried
or towed.
4) When negotiating curves, be aware of the variation in centri-
fugal force exerted in a position other than that of the center
of gravity, with and without the equipment in tow. Also pay
greater attention on sloping roads or ground.
5) For transport, adjust and fasten the lateral lifting arm chains
of the tractor; lock the hydraulic lifting control lever;
6) For displacements beyond the work area, the equipment must
be placed in the transportation position.
7) Upon request the Manufacturer will supply supports and tables
for signaling of dimensions.
8) When the dimensions of carried or partially-carried equipment
conceal the tractor's signalling and lighting devices, these
must also be installed on the equipment itself, in conformity
with regulations of the highway code of the country involved.
When in operation make sure that the lighting system is in
perfect working order.
Safety measures concerning the hydraulics
1) At the moment of connecting the hydraulic tubes to the
hydraulic system of the tractor, make sure that the hydraulic
systems of the operating machine and the tractor are not under
pressure.
2) For the operative hydraulic connections between tractor and
operating machine, the sockets and plugs should be marked
with colours to distinguish them, to avoid them being used
wrongly. There would be a danger of accident if the connections
were to be swapped round.
3) The hydraulic system is under high pressure; because of
the accident risk, when searching for leakage points special
auxiliary instruments should be used.
4) Not to never carry out the search losses with the fi ngers or the
hands. The liquids that exit from the holes can be nearly not
visible.
5) During transport by road the hydraulic connections between
tractor and operating machine should be disconnected and
secured to the support provided.
6) Do not use vegetable oils under any circumstance. These
could cause a risk of damage to the cylinder gaskets.
7) The operating pressures of the hydraulic system should be
between 100 bars and 180 bars.
8) Never exceed the indicated hydraulic system pressure levels.
9) Check that the quick hook-ups are coupled correctly; parts of
the system could get damaged if they are not.
10) Oil escaping at high pressure can cause skin injury with the
risk of serious wounds and infection. Call a doctor immediately
if such an incident occurs. If the oil with surgical means is not
removed quickly, can take place serious allergies and/or infec-
tions. Therefore, the installation of hydraulic components in the
tractor driver's cab is strictly forbidden. All the components of
the system should be positioned carefully to avoid parts being
damage during use of the equipment.
11) In case of participation on the hydraulic system, to unload the
hydraulic pressure carrying all the hydraulic commandos in all
the positions some times after to have extinguished the motor.
44 - EN
USE AND MAINTENANCE
Maintenance in safety
During work and maintenance operations, use suitable per-
sonal protection gear:
Overalls
1) Do not proceed with maintenance and cleaning if the power
take-off has not been disconnected fi rst, the engine power off,
the hand brake pulled and the tractor blocked with a wooden
block or stone of the right size under the wheels.
2) Periodically check that the bolts and nuts are tight, and if
necessary tighten them again. For this it would be advisable
to use a torque wrench, respecting the values of 53 Nm for
M10 bolts, resistance class 8.8, and 150 Nm for M14 bolts
resistance class 8.8 (Table SV1).
3) During assembling, main-tenance, cleaning, fi tting, etc., with
the seeding machine raised, place adequate supports under
the equipment as a precaution.
4) The spare parts must correspond to the manufacturer's spe-
cifi cations. Use only original spares.
Gloves Shoes Goggles Hardhat
Tabella SV1
cod. F07011705