Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
2.2 SAFETY REGULATIONS AND ACCIDENT
PREVENTION
Pay attention to
danger signs, where shown, in this booklet.
There are three levels of danger signs:
• DANGER: This sign warns that the operations described cause
serious lesions, death or long term health risks, if they are not
carried out correctly.
• ATTENTION: This sign warns that the operations described
could cause serious lesions, death or long term health risks, if
they are not carried out correctly.
• CAUTION: This sign warns that the operations described could
cause serious damage to the machine. if they are not carried out
correctly.
In order to complete the various levels of danger, the following
describe situations and specifi c defi nitions that may directly involve
the machine or persons.
• DANGER ZONE: any area inside a/o near a machine in which the
presence of an exposed person constitutes a risk for the safety
and health of that person.
• EXPOSED PERSON: Any person who happens to be completely
or partially in a danger zone.
• OPERATOR: The person/s charged with installing, starting up,
adjusting, carrying out maintenance, cleaning, repairing or tran-
sporting a machine.
• USER: The user is the person or the organization or the fi rm
which has purchased or rented the machine and intends to use
it for the purposes it was conceived for.
• SPECIALIZED PERSONNEL: Those persons who have been
specially trained and qualifi ed to carry out interventions of main-
tenance or repair requiring a particular knowledge of the machine,
its functioning, safety measures, methods of intervention - and
who are in a position to recognize the potential dangers when
using the machine and are able to avoid them.
• AUTHORIZED SERVICE CENTER: The authorized Service
Center is a structure legally authorized by the manufacturer which
disposes of personnel specialized and qualifi ed to carry out all
the operations of assistance, maintenance and repair - even of
a certain complexity - found necessary to keep the machine in
perfect working order.
Carefully read all the instructions before using the machine;
if in doubt, contact the technicians of the Manufacturer's
dealer. The manufacturer declines all responsibility for the
non-observance
of the safety and accident prevention regulations described
below.
General norms
1) Pay close attention to the danger signs in this manual and on
the machine.
2) The labels with the instructions attached to the machine give
abbreviated advice for avoiding accidents.
3) Scrupulously observe, with the help of the instructions, the
safety and accident prevention regulations.
4) Avoid touching the moving parts in any way whatsoever.
5) Any work on and adjustment to the machine must always be
done with the engine switched off and the tractor blocked.
6) People or animals must not, under any circumstances be
transported on the equipment.
7) It is strictly prohibited to drive the tractor, or allow it to be driven,
with the equipment attached by persons not in possession of
a driver's license, inexpert or in poor conditions of health.
8) Before starting the tractor and the equipment, check that all
safety devices for transport and use are in perfect working
42 - EN
USE AND MAINTENANCE
order.
9) Before starting up the equipment, check the area surrounding
the machine to ensure that there are no people, especially
children or pets, nearby, and ensure that you have excellent
visibility.
10) Use suitable clothing. Avoid loose clothing or garments with
parts that could in any way get caught in the rotating or moving
parts of the machine.
11) Before starting work, familiarize yourself with the control de-
vices and their functions.
12) Only start working with the equipment if all the protective devi-
ces are in perfect condition, installed and in the safe position.
13) It is absolutely prohibited to stand within the machine's radius
of action where there are moving parts.
14) It is absolutely forbidden to use the equipment without the
guards and container covers.
15) Before leaving the tractor,lower the equipment hooked to the
lifting unit, stop the engine, pull the hand brake and remove
the key from the dashboard, make sure that the chemical
substances safely out of reach.
16) The driver's seat must never be left when the tractor engine
is running.
17) Before starting the equipment, check that the supporting feet
have been removed from under the machine; check that the
machine has been correctly assembled and regulated; check
that the machine is in perfect working order, and that all the
parts subject to wear and tear are in good condition.
18) Before releasing the equipment from the third point attachment,
put the hoist command lever into the locked position and lower
the support feet.
19) Only operate when visibility is good.
20) All operations must be carried out by expert personnel,
equipped with protective gloves, in a clean and dust-free
environment.
Tractor hitch
1) Hook the equipment to a suitable, suffi ciently-powered tractor
by means of the appropriate device (lifter), in conformity with
applicable standards.
2) The class of the equipment attachment pins must be the same
as that of the lifter attachment.
3) Take care when working within the range of the lifting arms as
this is a very dangerous area.
4) Be very careful when hooking and unhooking the equipment.
5) It is absolutely forbidden to stand between the tractor and
linkage for manoeuvring the lifting controls from the outside
(fi g.3)
6) It is absolutely forbidden to stand in the space between the
tractor and the equipment
It is possible to work between the tractor and the equipment
only after the parking brake has been applied and a suitably
sized blocking wedge or stone has been placed under the
wheels.
7) The attaching of additional equipment onto the tractor brings
about a different distribution of weight on the axles. Check the
compatibility of the tractor performance with the weight that
the machine transfers onto the three-point linkage. If in doubt
consult the tractor Manufacturer.
8) Comply with the maximum admissible weight for the axle, the
total mobile weight, transport regulations and the highway
code.
CARDAN SHAFT
haft must bear the suitable safety markings for the country
(CE or other). It must always have its own instructions sheet
to be adhered to and the guard bearing the marking must be
wholly intact.
Assemble, operate and disconnect the cardan shaft always
according to information and safety standards supplied for
(fi g.3)
with the engine running.
cod. F07011705
Werbung
Inhaltsverzeichnis
