Installation - Scheppach HMS1080 Original Bedienungsanleitung

8.4 Crank handle for thickness planer chip depth
(fig. 8)
• The crank handle (12) will be only plugged on the
spindle.
8.5 Chip extraction (fig. 10)
• To mount the extension of the chip extraction (5a),
open the Phillips screw on the extension. Fit both
parts (5, 5a) together and retighten the Phillips
screw.
8.6 Chip extractor - surface planing (fig. 11+12)
• Set the planing knife cover cpl. (9) in the upperst
position.
• Use the crank handle (12) to place the Thickness-
ing table (21) in the lowest position.
• Take the chip extractor (5) and hold the switching
pins (3) beside. Place the chip extractor (5) at a
slightly slanting angle on the machine and push it
backwards. For this you need to hold the switching
pins (3) outwards.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins are incorrectly plugged in.
• Now you can fold the planing knife cover cpl. (9)
down again.
8.7 Chip extractor - thickness planing
(fig. 13+14)
• The parallel stop (8) needs to be removed for thick-
ness planing. Follow point 8.3 in reverse order.
• Hold the switching pins (3) outside and set the chip
extractor (5) on top of the machine.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.

9. Installation

m IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
Before each use, check the following:
• Proper function of the on and off button, incl. the
emergency switch (if available).
• Locked disconnected protective equipment
(fig 1a - pos. 3)
by gradual opening of every separating protective
equipment to be able to turn the machine off and
checking that the machine cannot be turned on
whenever the protective equipment is open
• Brake
Switch on the machine at the start of work and
allow the machine to reach speed. Now switch the
machine off again. The engine must come to a
standstill within 10 seconds. Otherwise, there is a
defect.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Anti-kick claws (fig. 9 - pos. 20)
at least once per shift by a visual inspection to
establish that they are in good working order, for
example, that the contact surface has not been
damaged by impacts and that the anti-kick claws
(25) fall back without hindrance due to their own
weight;
• Planing blades (fig. 17 - pos. 25)
for signs of damage and to ensure they are posi-
tioned correctly.
The machine may only be used if all these condi-
tions are satisfied.
Use only well sharpened and maintained blades. Use
only blades that are designed for the machine.
Use pusher wood or sticks which are in perfect con-
dition for machining short workpieces.
Connect the machine to a dust and chip extractor.
Check that the stop is secure before starting the ma-
chining work.
Ensure that you can maintain your balance at all
times. Stand to the side of the machine.
Whilst the machine is running keep your hands at
a safe distance from the cutting block and from the
point at which the chips are discharged.
Do not start the planing work until the cutting block
has reached the required speed.
Also ensure that the workpiece does not contain any
cables, wires, cords or the like. Do not machine any
wood which has lots of knots or knot holes.
Secure long workpieces to prevent them tipping over
at the end of the planing process. Use roller stands,
for example, or similar devices for this purpose.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
Switch off the machine immediately it is jams. Pull out
the mains plug and remove the jammed workpiece.
Set the smallest cutting size after use to prevent the
risk of injury.
m CAUTION!
The machine must be secured to the floor / counter-
top using suitable screws / screw clamps since oth-
erwise there is a risk that it will tip over.
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.