Technical Data; Unpacking; Assembly - Scheppach HMS1080 Original Bedienungsanleitung

6. Technical data

Number of knives
Cutter block rpm
Dimensions
Weight
Technical data – Surfacing
Max planing width
Max chip removal
Ripping fence l x h
Ripping fence tilting angle
Surfacing table size
Technical data – Thicknessing
Max planing width
Max planing thickness
Max chip removal
Thicknessing table size
Drive
Motor V/Hz
Consumption power P1
Subject to technical changes!
Noise
Total noise values determined in accordance with EN
61029.
Sound pressure level L .............................. 92 dB(A)
pA
Uncertainty K .................................................... 3 dB
pA
Sound power level L ................................ 105 dB(A)
WA
Uncertainty K ................................................... 3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were
measured in accordance with a standardised test
procedure and can be used to compare one power
tool with another.
The above-mentioned noise emission values can
also be used for the preliminary assessment of ex-
posure.
Warning:
• The noise emissions during the actual use of the
power tool may differ from the above-mentioned
values depending on the power tool being used,
in particular on the type of workpiece being pro-
cessed.
• Try to keep emissions as low as possible, for ex-
ample by limiting your working time. In this regard,
all the operational cycle phases must be taken into
consideration (such as the times when the tool is
switched off or running idle).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2 pieces
9000 1/min
945 x 450 483 mm
26,5 kg
254 mm
2 mm
640 x 127 mm
90°–135°
920 x 264 mm
254 mm
120 mm
2 mm
350 x 270 mm
230-240V / 50 Hz
1500 W

7. Unpacking

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage. Inform the transport agent imme-
diately of any faults. Later complaints cannot be
considered.
• If possible, store the packaging until the warranty
period has expired.
• Familiarize yourself with the machine with the help
of the operating instructions manual before using
it.
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

8. Assembly

m IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
8.1 Rubber feet (fig.2)
Secure the four rubber feet (15) to the bottom side of
the equipment using the Allen screws (A) and wash-
ers (B) supplied.
8.2 Planing blade cover (fig. 3-5)
• First remove the Phillips screw (19) and the fasten-
ing nut (10) on the planer blade cover (9) and the
fastening nut (6) on the swivel arm for planing blade
cover (9a).
• Push the planing blade cover (9) and the swivel arm
(9a) together.
• Retighten fastening nut (10) and Phillips screw (19).
• Fasten the assembly to the holes shown in Fig. 4
using the fastening nut (6) and the star grip screw
(4)
8.3 Parallel stop (fig. 6+7)
• Now attach the parallel stop (8) to the machine
housing and fasten it using the Allen screws (C).
GB | 25