General Safety Rules; Work Area Safety; Electrical Safety; Personal Safety - Ryobi RHT400 Bedienungsanleitung

GB
F D E

GENERAL SAFETY RULES

GENERAL POWER TOOL SAFETY WARNINGS
WARNING
R e a d a l l s a f e t y w a r n i n g s a n d a l l
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
n
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark
n
areas invite accidents.
Do not operate power tools in explosive atmospheres,
n
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep children and bystanders away while operating
n
a power tool. Distractions can cause you to lose
control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify
n
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or grounded
n
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
n
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for
n
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use an
n
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
If operating a power tool in a damp location is
n
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
I P NL S DK N FIN GR HU CZ RU
English
NOTE: The term "residual current device (RCD)" may be
replaced by the term "ground fault circuit interrupter
(GFCI)" or "earth leakage circuit breaker (ELCB)".

PERSONAL SAFETY

Stay alert, watch what you are doing and use
n
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
Use personal protective equipment. Always wear eye
n
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is
n
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
n
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance at
n
all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or
n
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
If devices are provided for the connection of dust
n
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
n
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
n
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect t he plug from the power source and/or
n
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
9
RO PL SLO HR TR EST LT LV SK BG