Program Change; Pitch Bend; Channel Aftertouch - Yamaha PLG150-AN Bedienungsanleitung

1.4 Program change

This message is used to switch voices.
It changes the program number on the receiving channel. When the change is to
include the voice bank, transmit the program change after sending the Bank
Select message (see 1.2.1).
If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not
receive program changes.

1.5 Pitch bend

This message conveys information on pitch bend operations.
Basically, this message is for changing the pitch of a part, but the depth of the fol-
lowing six effects can be controlled.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO FMOD DEPTH
6. BEND LFO AMOD DEPTH
By default, the Pitch Control effect is applied.
If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will
not receive pitch bend messages.

1.6 Channel aftertouch

This message conveys the pressure after the key is played on the keyboard (for an
entire MIDI channel). The pressure can be controlled for each part. This message
will affect the notes currently playing.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO FMOD DEPTH
6. CAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Channel Aftertouch.
2. System exclusive messages
2.1 Parameter changes
This device uses the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI System On
[ DX1 PARAMETER CHANGE]
1) DX1 Master Tuning
[ XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Part parameter change
4) PLG150-AN Part Assign parameter change
[ PLG150-AN NATIVE PARAMETER CHANGE ]
1) PLG150-AN System parameter change
2) PLG150-AN Part parameter change
3) AN1x System parameter change
4) Current Voice Common parameter change
5) Current Voice Scene parameter change
6) Currnet Voice Step Seq. Patten parameter change
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
F0H
11110000
01111111 7FH
7FH
01111111
04H
00000100
01H
00000001
* 0sssssss SSH
0ttttttt TTH
F7H
11110111
or
F0H
11110000
7FH
01111111
0xxxnnnn XNH
04H
00000100
00000001 01H
SSH
0sssssss
0ttttttt TTH
F7H
11110111
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Real Time
= Device Number, xxx = don't care
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
When received, the Volume MSB is reflected in the System Parameter MAS-
TER VOLUME.
* The binary expression 0sssssss is expressed in hexadecimal as SSH.
The same applies elsewhere.
2.1.2 Universal non-realtime messages
2.1.2.1 General MIDI System On
F0H = Exclusive status
11110000
7EH = Universal Non-Real Time
01111110
01111111 7FH = ID of target device
09H = Sub-ID #1=General MIDI Message
00001001
00000001 01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
11110111
or
F0H = Exclusive status
11110000
7EH = Universal Non-Real Time
01111110
0xxxnnnn XNH = N:Device Number, X:don't care
09H = Sub-ID #1=General MIDI Message
00001001
00000001 01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
11110111
When this message is received, the XG parameters are initialized.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3 DX1 MASTER TUNING
11110000 F0H Exclusive status
43H YAMAHA ID
01000011
0001nnnn 1NH N:device Number
04H
00000100
01000000 40H
VVH Data
0vvvvvvv
F7H End of Exclusive
11110111
The DX1-compatible messages are received, and the Master Tune of the
AN1x System Data is changed.
The value of VV is used as the MIDI master tuning parameter.
VV = -64(00H) — 0(40H) — +63(7FH)
2.1.4 XG Parameter Change
This message sets XG-related parameters. Each message can set a single
parameter.
The message format is as follows.
11110000 F0H Exclusive status
43H YAMAHA ID
01000011
1NH N:device Number
0001nnnn
01001100 4CH Model ID
GGH Address High
0ggggggg
0mmmmmmm MMH Address Mid
LLH Address Low
0lllllll
0vvvvvvv VVH Data
: :
F7H End of Exclusive
11110111
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
2.1.4.1 XG System On
F0H Exclusive status
11110000
43H YAMAHA ID
01000011
1NH N:device Number
0001nnnn
4CH Model ID
01001100
00000000 00H Address High
00H Address Mid
00000000
01111110 7EH Address Low
00H Data
00000000
F7H End of Exclusive
11110111
When ON is received, the XG parameters are initialized.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.4.2 XG System parameter change
This message sets the XG SYSTEM block (see Tables <1-1> and <1-2>).
2.1.4.3 Multi Part parameter change
This message sets the Multi Part block (see Tables <1-1> and <1-3>).
2.1.4.4 Part Assign parameter change
This message sets the part assigned to PLG150-AN (see Tables <1-1> and
<1-4>).
MIDI Data Format
53