Lifting The Vehicle; Lowering The Vehicle - Formula 1 FJ250 Originalbetriebsanleitung

22. Only use accessories that are supplied with the
appliance.
Attention!
23. Position the floor jack in such a way that it only lifts
the vehicle in areas which are suitable according to
the model.
24. After lifting the vehicle, always support the load with
appropriate vehicle supports before working on the
vehicle.
25. Do not overload the floor jack beyond its rated ca-
pacity. This can lead to damage to the floor jack and
cause the floor jack to stop working properly.
26. This floor jack is only designed for use on hard, even
surfaces that are capable of supporting the load.
Using the appliance on other surfaces can lead to
instability and may cause the load to slip.
27. Centre the load on the lifting plate before lifting the
vehicle. Loads arranged off centre can lead to the
load slipping or damage to the floor jack as well as to
your vehicle.
28. Should it become difficult to lower the jack as
desired, always secure the vehicle with jack stands
against unexpected sinking. Obtain a second jack that
allows you to lift the vehicle high enough to be able
to safely remove the broken jack. In case of uncer-
tainty, ask for help from a professional.
29. KEEP YOUR HANDS AND FEET AWAY FROM THE
FLOOR JACK'S HINGE MECHANISM AND FROM
THE FLOOR CONTACT AREA WHEN LOWERING THE
LOAD!
30. THIS FLOOR JACK IS ONLY DESIGNED FOR LIFTING
ONE PART OF THE VEHICLE. DO NOT MOVE OR
REPOSITION THE VEHICLE WHILST IT IS LIFTED
WITH THE FLOOR JACK.
Always give the lifted vehicle additional support using
chassis stands. Never use the floor jack alone to sup-
port the load. Holding the load over long periods can
overload the appliance and lead to personal injury and
material damage.
Specification
Maximum load bearing capacity:
Lifting range with nominal load:

Lifting the vehicle

1. Ensure that the floor jack and the vehicle are on a
hard, even surface.
2. Always apply the handbrake and lock the wheels.
201221_10809_FloorJack_FJ250_BDA_Inhalt.indd 9 201221_10809_FloorJack_FJ250_BDA_Inhalt.indd 9
3. Look at the operating manual for information on how
to ensure the position of the lifting points for putting
the floor jack in place and position the floor jack
under the prescribed lifting point.
4. Turn the release valve clockwise in the closed
position. DO NOT TURN THE VALVE BEYOND THE
CLOSED POSITION.
5. To lift the vehicle to the required height, insert the
handle into the socket and make up and down pump-
ing movements with the handle.
6. Place the chassis stands under the vehicle at the
places recommended by the vehicle manufacturer. Do
not go underneath the vehicle if it is not supported
by appropriate chassis stands. Floor jacks are not
designed to hold heavy loads over a long period.

Lowering the vehicle

1. Remove the chassis stands. Take care that neither
you nor any other person is under the vehicle whilst it
is being lowered.
2. Turn the release valve anti-clockwise SLOWLY to
lower the vehicle onto the floor.
Inspec tion
The product must be maintained according to the
product instructions. No modifications may be made to
this product.
1. Before use, a visual check must be carried out with
regard to any unusual state of the appliance, such as
cracked welding seams, damage, bent, worn, loose or
missing parts.
2. The appliance check must be carried out in accordan-
ce with the instructions in this manual.
3. The product must be checked straight away if you
know that it has been exposed to unusual loads or
knocks. The owners and/or operators should be
aware that repairing this product requires special
equipment and knowledge. (See #4 in the Maintenan-
ce section).
2 tonnes
89 – 359 mm
Maintenance
Maintenance is recommended once a month. Lubrication
is of essential importance for floor jacks, as they support
heavy loads. Any restriction due to dirt, rust etc. can
cause either the floor jack to move more slowly or
extremely quick vibrations, which damage the internal
EN
9
English
18.01.21 14:29 18.01.21 14:29