Technical Data; Noise Information - AEG PS216L3 Originalbetriebsanleitung

TECHNICAL DATA

Mitresaw *
Production code
Rated input
No-load speed
Saw blade dia. x hole dia
Saw blade body thickness max.
Saw blade tooth thickness min.
Min. workpiece dimensions
Max. cutting capacity
Mitre 0° / Bevel 0°
Mitre 45° / Bevel 0°
Mitre 0° / Bevel 45°
Mitre 45° / Bevel 45°
Mitre 50° / Bevel 47°
Mitre 50° / Bevel 2°
Mitre 50° / Bevel 47°
Mitre 50° / Bevel 2°
GB
Weight according EPTA-Procedure 01/2014

Noise information

Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
*PS Mitresaw
^
=
WARNING!
The noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared noise emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, noise emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to noise should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of noise such as: maintain the tool and the accessories and
organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAWS
a) Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-off wheels
for cutting ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to jam.
Sparks from abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible.
If supporting the workpiece by hand, you must always
keep your hand at least 100 mm from either side of the saw
English
34 34
blade. Do not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your hand is placed
too close to the saw blade, there is an increased risk of injury from
blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be thrown at high
speeds, causing injury.
d) Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the saw
head and pull it out over the workpiece without cutting,
start the motor, press the saw head down and push the saw
through the workpiece. Cutting on the pull stroke is likely to
cause the saw blade to climb on top of the workpiece and violently
throw the blade assembly towards the operator.
PS216L3
4770 14 01 ...
... 000001-999999
220-240 V, 50 HZ, 1400W,
6,5 A
5000 min
-1
216 x 30 mm
1,6 mm
2,4 mm
130 x 35 x 2,5 mm
65 x 305 mm
65 x 215 mm
36 x 305 mm
36 x 215 mm
33 x 200 mm
33 x 200 mm
33 x 200 mm
33 x 200 mm
16,2 kg
98,45 dB (A)
111,45 dB (A)