Technical Data - AEG US 400 XE Originalbetriebsanleitung

TECHNICAL DATA

Reciprocating Saw
Production code
Rated input
Stroke rate under no-load
Lengths of stroke
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically,
the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty
K=5dB(A))
Sound power level (Uncertainty K=5dB(A)) 95,5 dB(A)
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN 62841
Cutting boards
with sawblade HCS 150 x 19 x 1,2 mm / 4,2 mm
Vibration emission value a
h, B
Uncertainty K=
Cutting wooden beams
with sawblade HCS 150 x 19 x 1,2 mm / 4,2 mm
Vibration emission value a
h, WB
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for diffe-
rent applications, with different accessories or poorly maintained,
the vibration and noise emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi-
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SABRE SAW SAFETY WARNINGS
US 400 XE
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
4749 65 01...
contact hidden wiring or its own cord. Cutting accessory con-
... 000001-999999
tacting a "live" wire may make exposed metal parts of the power
400 W
tool "live" and could give the operator an electric shock.
0-3500 min
-1 Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the workpiece by
13 mm
hand or against your body leaves it unstable and may lead to loss
1,7 kg
of control.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is re-
84,5 dB(A)
commended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not reach into the machine while it is running. Chips and splin-
ters must not be removed while the machine is running.
Always use the protective shields on the machine.
16,1 m/s
2
Do not use cracked or distorted saw blades.
1,5 m/s
2
Plunge cuts without pre-drilling a hole are possible with soft ma-
terials (wood, light building materials for walls). Harder materials
(metals) must first be drilled with a hole corresponding to the size
of the saw blade.
16 m/s
2
Always place the guide shoe on the workpiece when sawing.
1,5 m/s
2
Clamp your workpiece with a clamping device. Unclamped workpi-
eces can cause severe injury and damage.
To avoid unintended start of the product, place down tool only on
even surfaces.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
WARNING! Danger of burns
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Do not let any metal parts enter the airing slots - danger of short
circuit!
Always disconnect the plug from the socket before carrying out any
work on the machine.
GB
English
7