AEG PS216L3 Originalbetriebsanleitung Seite 40

Do not apply lubricants on the blade when it is running.
Never perform any cleaning or maintenance work when the
machine is still running and the head is not in the rest position.
Never attempt to stop a machine in motion rapidly by jamming
a tool or other means against the blade, serious accidents can be
caused unintentionally in this way.
Disconnect the saw from the mains supply or remove battery pack
before changing blades or carrying out maintenance.
Pay attention to blade packing and unpacking, it is easy to be
injured by the sharp blade tips.
Use a blade holder or wear gloves when handling a saw blade.
Keep and store the blade in original packaging or other suitable
packaging, keep in dry conditions and away from chemicals which
may damage the blade.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Always clamp the workpiece safely and securely.
Depending on the cutting operation and the size of the workpiece,
it may be neccessary to u se a C-clamp or other suitable clamp
instead of the work clamp to secure the workpiece prior to making
GB
the cut.
Ensure that the machine is always stable and secure (e.g. fixed to
a bench).
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear safety goggles when using the machine. It is recom-
mended to wear gloves for handling blades and rough material,
as well as sturdy non-slip shoes which also protect the feet from
workpieces that may fall from the cutting area.
Always make sure the power plug has been removed from the
mains power source before making adjustments, lubricating or
when doing any maintenance on the product.
Only plug-in when machine is switched off.
Never reach into the area near the blade, unless the blade has
completely stopped.
Before use, thoroughly check the tool for any damage or material
fatigue. Repairs should only be carried out by authorised Service
Agents.
Always use the guards on the machine. Do not use the machine if
the guards are not in place and working correctly.
The lower blade guard should only open when the blade is lowered
to the workpiece and must always be able to move freely and close
automatically..
Always fix and use extension bar holders for workpiece support
during operation.
Never alter of modify the saw or its function. Your safety may be
compromised.
Do not use saw blades which are cracked, damaged, or deformed.
Do not use saw blades made of high-speed steel.
Only use saw blades which are sharp. Replace blunt blades with a
new replacement.
Always use blades with correct size and shape of arbour holes.
Blades that do not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
Use only woodworking blades specified in this manual, which
comply with EN 847-1.
Do not use any flanges, washers, and nuts to secure the saw blade
other than those supplied or indicated in the instruction manual.
English
36 36
It is necessary to select a saw blade which is suitable for the mate-
rial being cut. Never use the product to cut materials other than
those specified in the intended use section in this manual.
It is important to avoid overheating the blade and melting the
plastic workpiece when cutting.
It is essential to adhere to the maximum speed specified on the saw
blade. only use saw blade that are marked with a speed equal or
higher than the speed marked on the tool.
Replace the table insert when worn or damaged.
Before work, make a dummy cut without the motor turned on so
the position of the blade, operation of the guards with respect to
other machine parts, and workpiece may be checked.
When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance from the blade.
Avoid uncontrolled release of the saw unit from the fully down
position.
The bracket stop must always be engaged when transporting the
product.
Keep the floor area free of loose material e.g. chips and cut-offs.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Long workpieces must be adequately supported.The working
area of the saw includes the whole extent of the workpiece. The
operator should secure this area from accidental contact from
other persons or objects which may move the workpiece during
operation.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not replace the LED or laser with a different type. Any repairs
must only be carried out by the manufacturer or authorised service
agent.
A power spike causes voltage fluctuations and may affect other
electrical products in the same power line. Connect the product
to a power supply with an impedance equal to 0.3 Ω to minimize
voltage fluctuations. Contact your electric power supplier for
further clarification.
SAFETY WARNINGS LASER
The laser radiation used in this saw is Class II with maximum P≤1mW
and λ:650nm wavelengths. Do not view directly with optical
instruments. Failure to comply with the rules could result in serious
personal injury.
Do not stare into beam during operation.
Do not project the laser beam directly into the eyes of others. Serious
eye injury could result.
Do not place the laser in a position that may cause anyone to stare
into the laser beam intentionally or unintentionally.
Do not use optical tools to view the laser beam.
Do not operate the laser around children or allow children to operate
the laser.
Do not attempt to repair the laser device by yourself.
Do not attempt to change any parts of the laser device by yourself.
Any repairs must only be carried out by the manufacturer or autho-
rised service agent.
Do not replace the installed laser with a different type.