Technical Data; Cut-Off Machine Safety Warnings - AEG BMMS18SBL-0 Originalbetriebsanleitung

TECHNICAL DATA

CUT-OFF MACHINE
Production code.....................................................................
Rated speed ..........................................................................
D=Cutting disk diameter max. ..........................
d=hole diameter ................................................
b=Cutting disk thickness min. / max. ................
Cutting depth max. ................................................................
Battery voltage.......................................................................
Weight according EPTA-Procedure 01/2014 (2.0...6.0 Ah) ...
Recommended ambient operating temperature ....................
Recommended battery types.................................................
Recommended charger .........................................................
Noise/vibration information (cutting concrete)
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound power level (Uncertainty K=3dB(A)) ........................
Sound pressure level (Uncertainty K=3dB(A))....................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a .............................................
h,SG
Uncertainty K ......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

CUT-OFF MACHINE SAFETY WARNINGS

a) The guard provided with the tool must be securely
attached to the power tool and positioned for maxi-
mum safety, so the least amount of wheel is exposed
towards the operator. Position yourself and bystanders
away from the plane of the rotating wheel. The guard
helps to protect operator from broken wheel fragments and
accidental contact with wheel.
b) Use only bonded reinforced or diamond cut-off
wheels for your power tool. Just because an accessory
can be attached to your power tool, it does not assure safe
operation.
c) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fl y apart.
d) Wheels must be used only for recommended
applications. For example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels
may cause them to shatter.
e) Always use undamaged wheel fl anges that are of
correct diameter for your selected wheel. Proper wheel
fl anges support the wheel thus reducing the possibility of
wheel breakage.
20 ENGLISH
BMMS18SBL BMMS18SBL
....................................... 4774 12 01... ....................................... 4774 12 01...
...000001-999999 ...000001-999999
........................................ 20000 min ........................................ 20000 min -1 -1
.............................................. 76 mm .............................................. 76 mm
.............................................. 10 mm .............................................. 10 mm
................................. 1 mm / 2,8 mm ................................. 1 mm / 2.8 mm
........................................... 16,3 mm ........................................... 16.3 mm
.............................................. 18 V .............................................. 18 V
..................................... 1.2...1.7 kg ..................................... 1,2...1,7 kg
........................................ -18...+50 °C ........................................ -18...+50 °C
L1860R, L1850R, L1840R, L1830R, L1825R, L1820R, L1815R, L1820S L1860R, L1850R, L1840R, L1830R, L1825R, L1820R, L1815R, L1820S
.................... BL1218, BLK1218; AL1218G; AL18G .................... BL1218, BLK1218; AL1218G; AL18G
......................................... 102,0 dB (A) ......................................... 102.0 dB (A)
........................................... 91,0 dB (A) ........................................... 91.0 dB (A)
............................................. 4.2 m/s ............................................. 4,2 m/s 2 2
............................................. 1.5 m/s ............................................. 1,5 m/s 2 2
f) Do not use worn down reinforced wheels from
larger power tools. Wheels intended for a larger power
tool are not suitable for the higher speed of a smaller tool
and may burst.
g) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be ade-
quately guarded or controlled.
h) The arbour size of wheels and fl anges must properly
fi t the spindle of the power tool. Wheels and fl anges with
arbour holes that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
i) Do not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If power tool
or wheel is dropped, inspect for damage or install an
undamaged wheel. After inspecting and installing the
wheel, position yourself and bystanders away from
the plane of the rotating wheel and run the power tool
at maximum no load speed for one minute. Damaged
wheels will normally break apart during this test time.
j) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The eye protec-
tion must be capable of stopping fl ying debris generated
by various operations. The dust mask or respirator must be
capable of fi ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
k) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear per-
sonal protective equipment. Fragments of workpiece or
of a broken wheel may fl y away and cause injury beyond
immediate area of operation.
l) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric
shock.
m) Never lay the power tool down until the accessory
has come to a complete stop. The spinning wheel may
grab the surface and pull the power tool out of your control.
n) Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
o) Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
p) Do not operate the power tool near fl ammable mate-
rials. Sparks could ignite these materials.
Further safety instructions for abrasive cutting-off
operations
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel. Pinching or snagging causes rapid stalling
of the rotating wheel which in turn causes the uncontrolled
power tool to be forced in the direction opposite of the
wheel's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a fi rm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque reactions
or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in line with the rotating
wheel. Kickback will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp ed-
ges etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain, woodcarving blade, seg-
mented diamond wheel with a peripheral gap greater
than 10 mm or toothed saw blade. Such blades create
frequent kickback and loss of control.
f) Do not "jam" the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and suscep-
tibility to twisting or binding of the wheel in the cut and the
possibility of kickback or wheel breakage.
g) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold the
power tool motionless until the wheel comes to a com-
plete stop. Never attempt to remove the wheel from the
cut while the wheel is in motion otherwise kickback
may occur. Investigate and take corrective action to elimi-
nate the cause of wheel binding.
h) Do not restart the cutting operation in the workpie-
ce. Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to mi-
nimize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
j) Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fl y apart.
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. AEG Distributors off er to retrieve
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least
10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
ENGLISH 21