Lavor TUCSON XL Montageanleitung Seite 20

EN
Information for supply may also be obtained from
the plug manufacturer.
230-240V
3G 2,5 mm
2
max 20 m
(if fitted)
Machines equipped with Total Stop:
- When the machine is working, by releasing the
gun lever, the motor stops automatically to pre-
vent component wear during the pump by-pass
phase (motor in stand-by).
- By pressing the gun lever the motor starts auto-
matically.
WARNING:
• do not leave the stand-by mode
active for more than 5 minutes.
- At the end of the operation, set the switch to
"OFF".
(if fitted)
Machines equipped with delayed, low-voltage Total
Stop:
- When the machine is working, by releasing the
gun lever, after approximately 15 seconds the
motor stops automatically to prevent component
wear during the pump by-pass phase (motor in
stand-by).
- By pressing the gun lever the motor starts auto-
matically.
WARNING:
• do not leave the stand-by mode
active for more than 5 minutes.
- At the end of the operation, set the switch to
"OFF".
IMPORTANT: (fig. 17 - pag. 7) It is advis-
able to put on the safety of the pistol trigger
whenever the machine is stopped, in order to
avoid unintentional starting.
- Any automatic start of the machine with-
out pressing the gun trigger is attribut-
able to air bubbles in the water or other
similar phenomena which do not imply
the existence of any defects in the ma-
chine.
- Please check that the coupling of the high
pressure hose with the appliance and the gun
supplied as standard equipments made cor-
rectly, that is to say without any water leak.
400-415V
4G 2,5 mm
2
max 30 m
> PRESSURE REGULATOR
If the appliance is equipped with a pressure reg-
ulator:
- when the pressure is set to minimum the T.S.may
not trigger. Therefore, do not allow the appliance
to function in by-pass for more than 1 minute.
- do not act on the gun lever too frequently (this may
cause a malfunction).
> INSTALLATION
1- Check that the master switch is turned to "OFF"
(fig. 6 - pag. 6) and that the water filter is fitted
into the pump's inlet pipe pos. 5 (fig. 7 - pag. 6).
2- Screw the snap connection into place by hand,
without the aid of tools pos. 10 (fig. 7 - pag. 6) .
3- Connect the water supply hose to the snap con-
nection . The hose must have an inside diameter
of at least 13 mm (1/2").
- Connect the high pressure hose to the pump's out-
let pipe pos. 4 (fig. 8 - pag. 6)(fig. 9 - pag. 6).
Press the high pressure hose coupling fully down
and then screw into place by hand without the
aid of tools.
- Connect the high pressure hose to the gun
(fig. 10 - pag. 6) .
- Turn the water tap fully on. The water tempera-
ture absolutely must be below 40°C.
IMPORTANTE:
The washer machine has to oper-
ate with clean water in order to avoid any dam-
ages to the washer machine itself.
- Release the gun safety catch and keep the trigger
pressed, allowing the water to flow until all the air
has been expelled (fig. 16 - pag. 7).
- Fit the lance into the gun (fig. 11 - pag. 6).
- Fit the nozzle into the lance.
- Connect the plug to the power socket.
> 1ST START-UP
When starting up for the first time or after a long
period out of use, connect the intake line only for
a few minutes so that any dirt is vented from the
delivery outlet
> START-UP
IMPORTANTE:
pressure cleaner, users are urged to hold the
20
Whenever using the high-
(0)