Initial Commissioning - SDMO Diesel 6000 A Silence C5 Benutzer- Und Wartungshandbuch

3.1 Key to illustrations
The cover illustrations can be used to identify the various components of the generating set. The procedures in the manual refer to
these illustrations using letters and numbers as identifiers: "A1" refers to the number 1 on figure A.
Earth terminal
Starter battery
Key
Fuel tap
Retention container
Oil level dipstick
Oil filler cap
Fuel level indicator
Fuel tank cap
APM202
Electrical connectors
Working hours counter
Stop lever
* Source transfer switch, battery charger, etc.
The unit may be equipped with the "GS101-Generator Smart Care" option (A28): the Bluetooth GSC101 box
transmits all the information needed to monitor the unit to an application to be installed on your mobile phone; this
includes maintenance dates, a maintenance aid, and the map of approved resellers for any spare parts required.
3.2

Initial commissioning

On taking delivery and commissioning the unit:
1. Check that it is complete and not damaged in any way.
2. If the unit is fitted with a transport bracket, remove it.
The transport bracket is a metal plate located underneath the engine, close to the earth terminal.
Although useful for transportation, it will prevent optimum operation of the unit (noise, vibration).
To remove it: lift the unit slightly and place it on a block then remove the nut (1) and the clamp (2).
3. Check the oil and fuel levels and top them up if necessary.
4. If necessary, connect the battery, starting with the positive terminal.
Observe the polarity of the battery terminals when connecting it: as this could cause serious damage to the electrical equipment.
Some units require a running-in period. Contact your nearest agent for more information.
3.3 Installing the battery
1. Connect the red wire to the positive battery terminal (+) (A2).
2. Connect the black wire to the negative battery terminal (-).
3.4 Connecting Generator Smart Care
The unit may be equipped with the "GS101-Generator Smart Care" option (A28):
1. Secure the Bluetooth GSC101 box to the unit,
2. Download and install the free Generator Smart Care* application onto a mobile phone or tablet,
3. Create an account,
4. Activate Bluetooth on the phone or tablet,
5. Follow the instructions on the application to pair the phone or the tablet with the Bluetooth GSC101 box.
Generator Smart Care displays all the information needed to monitor the unit in the application; this includes maintenance date
alerts and reminders, a maintenance aid, and the map of approved resellers for any spare parts required.
*Available free from the App Store and Google Play (excluding any connection fees charged by the phone system operator).
Before using the generating set
1. Check that it is correctly installed and that it is ready to start:
To carry out checks and starting operations, it is necessary to open the top cover and the access door of the generating set; close them
before starting the generating set.
2. Ensure that all of the procedures for use have been understood.
To stop the generating set as a matter of urgency, turn the key (
1086_EN.docx
A1 Oil drain tap
A2
Oil filter
A3
Fuel filters
A4
Generating set top cover
A5 Access door to the generating set
A6-B1 Fuse holder
A7 Panel lighting
A8 Circuit breakers
A9 Connection for options*
A10 Lifting eye
A11 Oil drain pipe
A12 Air filter
A13 Solenoid valve
Section 3. Getting started with the generating set
A14-B5 Exhaust silencer
A15-B6 Dipstick upper limit
A16 Dipstick lower limit
A17 Oil filter screw
A18 Hose clips
A19 Retaining clip
A20 Retaining clip screw
A21 Wheel
A22 Air filter cover
A23 Wing nut
A24 Paper element
A25 Rubber seal
A26 GSC101-Generator Smart Care
A3
) to the "OFF" position and close the fuel tap (
18/280
1
2
Section 4. Using the generator set
A4
).
2021-07-02
A27
B2
B3
B4
C2
C3
C4
D1
D2
D3
D4
D5
A28