Unloading; Move The Sweep Machine En; Start Up; General Notes - Kärcher KM 100/100 R Bp Originalbetriebsanleitung

Check fluid level in the battery and ad-
just if required
CAUTION
Regularly check the fluid level in acid-filled
batteries.
– The acid in a fully charged battery has a
specific weight of 1.28 kg/l at a temper-
ature of 20 °C.
– The acid in a partially discharged bat-
tery has a specific weight between 1.00
and 1.28 kg/l.
– The specific weight of the acid must be
uniform in all cells.
 Unscrew all cell caps.
 Take a sample from each cell using the
acid tester.
 Put the acid sample back into the same
cell.
 Where fluid level is too low, top up cells
to the mark provided with distilled wa-
ter.
 Charge battery.
 Screw in cell caps.

Unloading

DANGER
Risk of injury and damage! Do not use a
forklift to unload the appliance.
Note: Press the emergency-stop button to
immediately deactivate all functions and
turn the key switch to the "0" position.
To unload the machine, proceed as follows:
 Cut plastic packing belt and remove foil.
 Remove the elastic tape fasteners at
the stop points.
 Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
 Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
 Slide the four support beams included
in the packaging under the ramp.
 Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.
(1) Machine without built-in battery
 Loosen immobilizing brake (see "move
sweep machine").
 Slide the machine over the prepared
ramp from the pallet.
(2) Machine with built-in battery
 Connect battery (see section on Care
and maintenance)
 Release emergency-stop button by
turning.
 Set programme switch to step 1 (driv-
ing).
 Set main switch to "1".
 Slowly drive the appliance off the ramp.
 Set main switch back to "0".
Move the sweep machine
Danger
Risk of injury! Before releasing the immobi-
lizing brake, the machine must be secured
to prevent it rolling away. After releasing
the immobilizing brake, the machine roles
without brakes.
 Remove the brake level from the wheel
and put it in its position.
The immobilizing brake is thus deactivated;
the machine can now be moved.

Start up

General notes

 Park the sweeper on an even surface.
 Remove the key.
Inspection and maintenance work
 Check charging status of battery.
 Check side brush.
 Check roller brush.
 Shake off dust filter.
 Empty waste container.
 Check tyre pressure.
Note: For description, see section on Care
and maintenance.
5
-
EN

Operation

Adjusting driver's seat

 Open the hood, insert retaining rod.
 Release the wing nuts from the seat
rails.
 Slide the seat into the desired position.
 Tighten the wing nuts.
Note: If this adjustment is not enough, it
can be adjusted more.
 Remove 4 screws on the plate of the
seat contact switch.
 Remove the plate.
 Swivel the seat to the front.
 Loosen 4 screws on the seat support.
 Slide the seat and tighten the screws.
 Install the plate of the seat contact
switch.

Check charging status of battery

– Indicator lamp glows green
Battery is charged.
– Indicator lamp glows yellow
Battery is almost discharged.
 Terminate the sweeping operation and
charge the battery.
– Indicator lamp blinks red
Discharging limit has been reached. Anoth-
er 3 minutes of driving operation remain;
then the appliance will switch off.
 The appliance cannot be restarted, the
battery must be charged for at least 3
hours.
– Indicator lamp glows red
Battery is discharged. The control has
switched off the sweeping system.
 Charge battery.
21