Bosch AdvancedGrind 18 Originalbetriebsanleitung Seite 22

22 | English
a)
(26) Round nut
a)
(27) Cup brush
a)
(28) Open-ended spanner
(29) Extraction guard for cutting with cutting guides
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Angle grinder
Article number
Rated voltage
A)B)
Rated speed min
Speed adjustment range min
Max. grinding disc diameter/ mm
rubber sanding pad diameter
Grinding spindle thread
Max. thread length of grind- mm
ing spindle
Constant electronic control
Speed preselection
Soft start
Restart protection
Overload protection
Weight according to EPTA-
C)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
D)
ure during operation and
during storage
Recommended rechargeable
batteries
Recommended battery char-
E)
gers
A) Measured at 20–25 °C with rechargeable battery PBA 18V
6.0Ah.
B) Rated no-load speed for the selection of appropriate application
tools in accordance with EN IEC 62841-2-3. The actual speed is
lower for safety reasons and according to production toler-
ances.
C) Depends on battery in use
D) Limited performance at temperatures < 0 °C
E) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according to
EN IEC 62841-2-3.
Typically the A-weighted noise level of the power tool are: 89
dB(A); sound power level 97 dB(A). Uncertainty K = 3 dB.
1 609 92A 75F | (15.02.2022)
Wear hearing protection!
Vibration total values a
determined according to EN IEC 62841-2-3:
Surface grinding (roughing) and abrasive cutting:
a)
a
Disc sanding:
a
Grinding thin metal sheets or other materials that tend to easily vi-
brate with a large surface area can cause the noise emission value to
increase by up to 15 dB. Suitable, heavy damping mats can reduce
the increased noise emissions. Increased noise emissions must be
AdvancedGrind 18
taken into consideration, both for the risk assessment of the noise
output and for selecting suitable hearing protection.
3 603 CD9 0..
The vibration level and noise emission value given in these
V= 18
instructions have been measured in accordance with a
-1
11500
standardised measuring procedure and may be used to com-
-1 pare power tools. They may also be used for a preliminary
2800–11500
estimation of vibration and noise emissions.
125
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
M 14
power tool is used for other applications, with different ap-
21.7
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
●
working period.
●
To estimate vibration and noise emissions accurately, the
●
times when the tool is switched off or when it is running but
●
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
●
over the total working period.
kg 2.5 (2.5 Ah)–
Implement additional safety measures to protect the oper-
3.1 (6.0 Ah)
ator from the effects of vibration, such as servicing the
°C 0 to +35
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
°C –5 to +50
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
PBA 18V...W-.
interrupted.
To restart the tool, set the on/off switch (4) to the off posi-
AL 18...
tion and then switch the power tool on again.
Constant Electronic control
The Constant Electronic keeps the speed at no load and un-
der load virtually consistent, guaranteeing uniform perform-
ance.
Soft start
The electronic soft start limits the torque when the power
tool is switched on and increases the service life of the mo-
tor.
Speed preselection
You can select the required speed using the speed preselec-
tion thumbwheel (7), even during operation. The informa-
tion in the table below describes the recommended values.
(triax vector sum) and uncertainty K
h
2 2
= 10.0 m/s , K = 1.5 m/s ,
h
2 2
= 4.0 m/s , K = 1.5 m/s .
h
Bosch Power Tools