Technical Data; Noise/Vibration Information - Bosch PFS 55 Originalbetriebsanleitung

OBJ_BUCH-670-002.book Page 16 Monday, August 22, 2011 1:10 PM
16 | English
8 Air filter
9 Spray gun
10 Suction tube with container seal
11 Container for spray material, 600 ml
Container for spray material, 800 ml*
12 Vent cover
13 Air cap
14 Union nut
15 Thumbwheel for spraying capacity
16 Trigger switch
17 Venting hose
18 Venting valve
19 Membrane
20 Nozzle
21 Nozzle seal
22 Measuring cup
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Fine-spray System
Article number
Rated power input
Spraying capacity
Atomising output
Required time for application
2
of paint on 5 m
Container capacity for spray
material
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 74 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a <2.5 m/s , K= 1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
1 609 929 Y12 | (22.8.11)
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, Dept. PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
PFS 55
3 603 B06 0..
W 280
g/min 0–110
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
W 55
Leinfelden, 22.08.2011
min 12 Assembly
Before any work on the machine itself, pull the mains
ml 600
plug.
kg 1.3
Mounting the Spray Gun and the Electrical Unit
/II (see figures A1
Connecting the Electrical Unit with the Spray Gun
– Insert the spray gun 9 onto the electrical unit 1 until it can
be heard to engage.
Removing the Electrical Unit
– Press and hold the two red SDS release buttons 4 and pull
the spray gun 9 out of the electrical unit.
Operation
Preparing for Operation
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, varnish and spray material, pay at-
tention to their environmental compatibility.
Preparing the Spray Surface
Note: Cover off the vicinity of the spray surface thoroughly
and generously.
Dr. Eckerhard Strötgen
Head of Product
Certification
A2)
–
Bosch Power Tools