Multiplex cockpit sx Bedienungsanleitung Seite 256

15.7.3. V-tail compensation inputs
Menus: TH -CO, SP -CO
15.8. Transmitter control settings
Dual-Rate and Exponential
for AILERON, ELEVATOR and RUDDER........54
15.8.1. Dual-Rate for AILERON, ELEVATOR, RUDDER
) DR
Menu: ( CONTRL
15.8.2. Setting the Exponential function
) EXP
CONTRL
Menu: (
15.9. Activating flight phases.....................................55
15.9.1. What is possible with flight phases?
15.9.2. Activating flight phases
Menu: ( SETUP , MODEL
15.9.3. On-screen display of the active flight phase
15.9.4. Copying flight phases
) COPY
PHASENS
Menu: (
15.9.5. Setting the transition speed for switching flight phases
) SPEED
PHASES
Menu: (
15.10.Further possible functions
with the ACRO model type ...............................57
15.10.1. Combi-Switch
15.10.2. Push-button fixed values (automatic aerobatics)
) FIX
CONTRL
Menu: (
15.10.3. Deltas and flying wings
Menu: DELTA
15.10.4. Electronic Y-lead
) Y-LEAD
MIXER
Menu: (
16. Setting up a new model
Model type: HELI
16.1. What is possible with the HELI type? ...............59
16.1.1. Important information on flight phases!
16.1.2. Notes on the terms ROLL, PITCH-AXIS and YAW,
as used in the menus
16.2. Preparing the model .........................................59
16.2.1. Determining the rotor head type
16.2.2. Connecting the servos to the receiver
16.3. Preparing the transmitter ..................................60
16.3.1. Setting up a new memory for the HELI type
) NEW
MEMO
Menu: (
16.3.2. Setting the stick mode
(which stick controls which function?)
SETUP MODEL
Menu: ( ,
16.3.3. Transmitter controls for the HELI type
16.3.4. Setting the rotor head type
MIXER ROTOR
Menu: ( ,
16.3.5. Selecting the stick position for throttle idle / collective
pitch minimum
Menu: TH R (Reverse)
16.3.6. Throttle trim and the collective pitch stick
16.3.7. Selecting the right-hand slider minimum setting forward
/ back (Throttle Limiter and Direct Throttle)
SETUP, MODEL
Menu: (
Setting up Throttle Check Warning: "TH >0"
16.3.8.
16.4. Setting up the swashplate servos.....................63
16.4.1. Checking and correcting the direction of rotation
of the swashplate servos for COLLECTIVE PITCH 63
16.4.2. Checking the direction of rotation
of the swashplate servos for ROLL and PITCH
16.4.3. Setting up the swashplate for rotor head types 1 to 4 64
16.5. Setting the collective pitch curve
) PITCH.................................64
CONTRL
Menu: (
16.6. Everything about throttle...................................65
16.6.1. The meaning of Limiter, Curve, Minimum, Trim, DTC
and Throttle Cut
16.6.2. Setting up the throttle servo for a glow motor
54
54
54
55
) PHASES
55
56
56
56
57
57
58
58
59
59
59
59
60
60
) MODE
61
61
) TYPE
61
62
62
) SP+L R
62
63
63
65
65
Operating Instructions
16.6.3. Throttle for electric helicopters
16.6.4. Setting up the throttle curve
CONTRL
Menu: (
16.6.5. Setting throttle minimum (idle)
CONTRL
Menu: (
16.6.6. Setting throttle for auto-rotation
CONTRL
Menu: (
16.7. Setting up the tail rotor
Menu: TAIL.....................................................67
16.7.1. Checking / correcting the direction of rotation, centre
and maximum travel of the tail rotor
Setting the YAW input for the tail rotor
16.7.2.
16.7.3. Zero point for tail rotor mixers
Menu: ( MIXER
Setting the CP input for the tail rotor (REVO-Mix) 68
16.7.4.
Setting an OFFSET for the tail rotor
16.7.5.
16.8. The helicopter gyro
MIXER
Menu: (
16.8.1. Setting gyro gain
16.8.2. Activating HEADING mode
CONTRL, GYRO
Menu: (
16.8.3. Checking the heading function
16.9. Transmitter control settings
Dual Rate and Exponential
for ROLL, PITCH-AXIS and YAW.....................70
16.9.1. Setting Dual Rate for roll, pitch-axis and yaw
CONTRL
Menu: (
16.9.2. Adjusting the Exponential function
CONTRL
Menu: (
16.10.Activating flight phases .....................................71
16.10.1. What is possible with flight phases?
16.10.2. Activating flight phases
Menu: PHASES
16.10.3. On-screen display of the active flight phase
16.10.4. Copying flight phases
PHASES
Menu: (
16.10.5. Setting the transition speed for switching flight phases
Menu: ( PHASES
16.11.Virtual swashplate rotation
(MIXER ROTOR)
Menu:
17. The free mixers MIX 1, 2 and 3
17.1. Defining / adjusting the free mixers
Menu: ( MIXER
17.2. Adjusting the mixer effect .................................73
17.3. Erasing the free mixers.....................................74
18. Managing model memories
Menu: MEMO
18.1. Switching the model memory
Menu: ( MEMO
18.2. Setting up a new model
MEMO
Menu: (
18.3. Entering / changing the model name
MEMO
Menu: (
18.4. Copying model memories
MEMO
Menu: (
18.5. Erasing model memories
Menu: ( MEMO
19. Timers 1 and 2, operating time
19.1. Timer 1..............................................................76
19.1.1. Assigning a switch
TIMER
Menu: (
19.1.2. Operating Timer 1 with an alarm
TIMER
Menu: (
Page 3
) TH
) TH MIN
) TH AR
) CP ZRO
, TAIL
) GYRO .......................................69
) HEADG
) DR
) EXP
) COPY
) SPEED
V-ROT .......................72
) MIXDEF..................................73
) GO TO ......................................74
) NEW............................................75
) NAME .........................................75
) COPY .........................................75
) DELETE ....................................76
) T1 SW
) START1
66
66
66
67
67
68
68
69
69
69
70
70
70
71
71
71
72
72
73
74
76
76
76